Paulo Alexandre Amorim

Dr. Paulo Alexandre Amorim

orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 June 2021 in Bioprinting
Verified
Journal Article
Closed access
Paulo Alexandre AmorimPaulo Alexandre Amorim
Paulo Alexandre Amorim
MDM.A. D’áVila
M.A. D’áVila
RAR. Anand
R. Anand
PMP. Moldenaers
P. Moldenaers
PPP. Van Puyvelde
P. Van Puyvelde
VBV. Bloemen
V. Bloemen

6 August 2021 in Frontiers in Bioengineering and Biotechnology
Verified
Journal Article
Open access
EREsther Reina-Romo
Esther Reina-Romo
SMSourav Mandal
Sourav Mandal
Paulo Alexandre AmorimPaulo Alexandre Amorim
Paulo Alexandre Amorim
VBVeerle Bloemen
Veerle Bloemen
EFEleonora Ferraris
Eleonora Ferraris
LGLiesbet Geris
Liesbet Geris
Research in bioprinting is booming due to its potential in addressing several manufacturing challenges in regenerative medicine. However, there are still many hurdles to overcome to guarantee cell survival and good printability. For the 3D extrusion-based bioprinting, cell viability is amongst one of the lowest of all the bioprinting techniques and is strongly influenced by various factors including the shear stress in the print nozzle. The goal of this study is to quantify, by means of in silico modeling, the mechanical environment experienced by the bioink during the printing process. Two ubiquitous nozzle shapes, conical and blunted, were considered, as well as three common hydrogels with material properties spanning from almost Newtonian to highly shear-thinning materials following the power-law behavior: Alginate-Gelatin, Alginate and PF127. Comprehensive in silico testing of all combinations of nozzle geometry variations and hydrogels was achieved by combining a design of experiments approach (DoE) with a computational fluid dynamics (CFD) of the printing process, analyzed through a machine learning approach named Gaussian Process. Available experimental results were used to validate the CFD model and justify the use of shear stress as a surrogate for cell survival in this study. The lower and middle nozzle radius, lower nozzle length and the material properties, alone and combined, were identified as the major influencing factors affecting shear stress, and therefore cell viability, during printing. These results were successfully compared with those of reported experiments testing viability for different nozzle geometry parameters under constant flow rate or constant pressure. The in silico 3D bioprinting platform developed in this study offers the potential to assist and accelerate further development of 3D bioprinting.

2 April 2022 in Carbohydrate Polymers
Verified
Journal Article
Closed access
MAMehdi Salar Amoli
Mehdi Salar Amoli
RAResmi Anand
Resmi Anand
Mostafa EzEldeenMostafa EzEldeen
Mostafa EzEldeen
Paulo Alexandre AmorimPaulo Alexandre Amorim
Paulo Alexandre Amorim
LGLiesbet Geris
Liesbet Geris
Veerle BloemenVeerle Bloemen
Veerle Bloemen

24 June 2022 in Biomedical Materials
Verified
Journal Article
Closed access
RAResmi Anand
Resmi Anand
MAMehdi Salar Amoli
Mehdi Salar Amoli
AHAn-Sofie Huysecom
An-Sofie Huysecom
Paulo Alexandre AmorimPaulo Alexandre Amorim
Paulo Alexandre Amorim
HAHannah Agten
Hannah Agten
VBVeerle Bloemen
Veerle Bloemen
Methacryloyl gelatin (GelMA) is a versatile material for bioprinting because of its tunable physical properties and inherent bioactivity. Bioprinting of GelMA is often met with challenges such as lower viscosity of GelMA inks due to higher methacryloyl substitution and longer physical gelation time at room temperature. In this study, a tunable interpenetrating polymer network (IPN) hydrogel was prepared from gelatin-hyaluronan dialdehyde (Gel-HDA) Schiff’s polymer, and 100% methacrylamide substituted GelMA for biofabrication through extrusion based bioprinting. Temperature sweep rheology measurements show a higher sol-gel transition temperature for IPN (30 °C) compared to gold standard GelMA (27 °C). Furthermore, to determine the tunability of the IPN hydrogel, several IPN samples were prepared by combining different ratios of Gel-HDA and GelMA achieving a compressive modulus ranging from 20.6 ± 2.48 KPa to 116.7 ± 14.80 KPa. Our results showed that the mechanical properties and printability at room temperature could be tuned by adjusting the ratios of GelMA and Gel-HDA. To evaluate cell response to the material, MC3T3-E1 mouse pre-osteoblast cells were embedded in hydrogels and 3D-printed, demonstrating excellent cell viability and proliferation after 10 d of 3D in vitro culture, making the IPN an interesting bioink for the fabrication of 3D constructs for tissue engineering applications.

2 September 2025 in Gels
Verified
Journal Article
Open access
PDF file
Paulo Alexandre AmorimPaulo Alexandre Amorim
Paulo Alexandre Amorim
HAHannah Agten
Hannah Agten
MVMargaux Vermeulen
Margaux Vermeulen
Sandra Van VlierbergheSandra Van Vlierberghe
Sandra Van Vlierberghe
LGLiesbet Geris
Liesbet Geris
Veerle BloemenVeerle Bloemen
Veerle Bloemen
Cartilage tissue engineering aims to restore damaged cartilage using biomaterials, cells, and/or biological cues to support cell growth and tissue repair. Although in the past decades scientific advances have moved the field forward, their translation to a clinical setting is still hampered. One major hurdle to take is to reduce process variability to ensure a predictable biological outcome. Using enabling technologies such as bioprinting has shown the potential to improve process robustness. However, developing bioinks that balance printability with biological functionality remains a major challenge. This study presents the development and structure–property relationships of a novel gelatin-based hydrogel blend, GelMA/GelMA-AEMA, optimized for extrusion-based bioprinting (EBB) while maintaining the crucial biological properties of GelMA for tissue engineering applications. The novel GelMA/GelMA-AEMA blend demonstrated superior flowability and printability compared to GelMA, effectively addressing common 3D-printing defects such as filament shape inhomogeneity. A systematic rheological characterization revealed that the blend exhibits a softer, elastically dominated structure with improved compliance. The blend behaves as a yield-stress fluid with a strong shear-thinning degree, making it highly suitable for EBB. The superior flow properties of the blend are deemed to enhance bond slippage and stress-induced orientation of its more imperfect gel structure, resulting in greater macroscopic deformation and enhanced print fidelity. In addition, histological assessment of a 21-day in vitro study with iPSC-derived chondrocytes suggested that the blend is at least equally performant as GelMA in supporting matrix formation. Histological analysis shows similar matrix deposition profiles, whereas gene expression analysis and compression tests even have suggested superior characteristics for cartilage TE. This study emphasizes the central role of rheology in bioink development and provides foundations for future material development for EBB, with potential implications for cartilage tissue engineering.