In the last two decades, high-rise timber buildings have been built using the glulam truss system, even with limited openings. Moment-resisting timber frames (MRTF) with semi-rigid beam-to-column connections can be an architecture-friendly way to provide a load-carrying system to vertical and horizontal loads for timber buildings. In these structures, connections of adequate ductility are crucial to ensure robustness and energy dissipation. This paper presents a review of the main types of timber beam–column moment connections with improved ductility and proposes to carry out a ductility assessment of these connections based on the most relevant ductility factors. Joints have a significant influence on the global performance of MRTF, and the application of ductile connections have improved the mechanical parameters of the timber frame. The reinforced bolted slotted-in steel plate and glued-in rods connections have similar mechanical performance, with high rotation capacity and good ultimate moment, but exhibited different failure modes under cyclic loading. The connections were classified within ductility classes. In general, the glued-in steel rods presented better results because of the high influence of steel profiles in the connection yielding. Despite the excellent mechanical behavior, the reinforced bolted slotted-in steel plate connections presented medium ductility values.
Despite their favorable physical and mechanical properties for structural use, tropical woods, such as Iroko (Milicia excelsa), present knowledge gaps to be filled mainly about their mechanical characterization, which currently limit their use or result in under- or overdimensioned structural elements. Visual classification, one of the most used methods for characterizing wood, is inaccurate in the case of Iroko due to the wide variety of geographical locations in which this species can be found. In addition, mechanical characterization using test pieces with structural dimensions leads to high and impractical costs. In this context, this study aims to verify the mechanical properties of Iroko (imported from the Republic of the Congo) from small size specimens, a process that is currently standardized only for softwoods, and to verify the correlation of different properties through bending properties and ultrasound tests. Prior to the bending tests, the speed of propagation of ultrasonic waves was measured using the direct method. The results obtained show a good correlation between density and bending properties and the velocity of propagation of ultrasonic waves.
1 January 2023 in Revista IBRACON de Estruturas e Materiais
The study proposes to analyze the distribution of bending moment due to live load in curved bridges that have undergone a process of widening, considering the influence of concrete’s strength variation. The results show that the bending moment redistribution is more significant the higher the stiffness in the widenings. In addition, the redistribution induced by the variation of stiffness depends on the live load positioning but, generally, it results in the migration of bending moments to the stiffer regions, relieving the original girders. The curvature did not significantly alter the response induced by the stiffening of the widened segments. Also, the divergences found between the MEF and the V-load Method results for models with uniform and variable stiffness were similar. Finally, the Modification Factors (MF) proved to be more sensitive to the influence of curvature than to the concrete strength in the widenings.
1 January 2022 in Revista IBRACON de Estruturas e Materiais
The present study focuses on comparative parametric analysis of curved precast concrete bridges using straight and curved I-girders. The live load bending moment distribution for girders was studied using the bridge curvature and its relationship with the results obtained for a straight bridge. FEM 3D models were developed with restrictions on the transverse live load positions and with two different load models types: HL-93 (AASHTO) and TB-450 (NBR 7188, 2013). The parametric analysis results were calculated using the Modification Factor (MF) and the Bending Moment Distribution Factor (BMDF), calculated from the structural analysis of each model at the midspan. Globally, an increase was found in the total bending moment for the curved bridge models in relation to the straight bridge. In the examples herein studied, the larger the bending radius, the larger the maximal bending moment in the bridge center. For the external girders, the MF increases with the increase of the L/R. For the internal ones, the MF decreases with the increase of the L/R. In addition, the occurrence of “Load Shift” was different from the rigid body behavior, for there was demonstrated a different bending moment variation between external girder (G1) in relation to its adjacent (G2). Therefore, the structural behavior of straight (SG) and curved girders (CG) was analyzed, revealing that, in the SG, a significant gap occurred in the BMDF between G1 and G2 girders for all curvatures. For L/R = 0.6, it caused a difference of 17.8% in the BMDF between the G1 and G2 girders, while on the curved girders, a difference of only 6.6% was found.