The gap of standardization for conducted and field coupled electromagnetic interferences (EMI) in the 2–150 kHz frequency range can lead to Electromagnetic Compatibility (EMC) problems. This is caused by power systems such as Pulse Width Modulation (PWM) controlled rectifiers, photovoltaic inverters or charging battery units in electric vehicles. This is a very important frequency spectral due to interferences generated in a wide range of devices and, specifically, communication problems in the new technologies and devices incorporated to the traditional grid to convert it into a Smart Grid. Consequently, it is necessary to provide new solutions to attenuate this kind of interference, which involves finding new materials that are able to filter the electromagnetic noise. This contribution is focused on characterizing the performance of a novel material based on nanocrystalline and comparing it to most common material compositions such as MnZn and NiZn. This research is carried out from the point of view of the manufacturing process, magnetic properties and EMI suppression ability. This last item is carried out through two analysis procedures: a theoretical method by determining the attenuation ratio by measuring impedance parameter and proposing a new empirical technique based on measuring directly the insertion loss parameter. Therefore, the main aim of this characterization process is to determine the performance of nanocrystalline compared to traditional cable ferrite compositions to reduce the interferences in this controversial frequency range. From the results obtained, it is possible to deduce that nanocrystalline cable ferrite provides the best performance to filter the electromagnetic noise in the 2–150 kHz frequency range.

It is crucial to extend the electromagnetic compatibility (EMC) studies to the new frequency regions where modern telecommunication systems operate, specifically those related to the fifth-generation (5G) technology standard for broadband cellular networks. Electric autonomous vehicles (EAVs) are systems that feature 5G technology on board and for which it is essential to ensure the proper management of EMC to prevent malfunctions. Given the considerable development of the EAV-related sector, new materials and solutions for EMI shielding with properties that reduce interference in the frequency regions of 5G technology are being investigated. Today, meatal-based solutions are the most common EMI shielding materials used to mitigate EMC problems. Nevertheless, with the appearance of EAVs, it is needed the design of novel materials that provide a significant balance in terms of shielding effectiveness (SE) and mechanical properties. Thereby, carbon nanotubes (CNTs) are an attractive alternative to conventional EMI shielding materials due to their characteristics. The lightweight condition, flexibility, cost-effectiveness, easy processing, and resistance to corrosion made this new type of material perfect to be used in the field of EAVs. This contribution focuses on describing and characterizing three nanocomposite materials manufactured by loading a polymer matrix with 5%, 7%, and 10% CNT concentrations, respectively. The SE measurement is carried out with a coaxial sample holder based on the standard ASTM D4935-18. This measurement setup makes it possible to determine the performance of the three materials under test up to 18 GHz, covering part of the operation frequencies of 5G systems.

Magnetic near-field probes (NFP) represent a suitable tool to measure the magnetic field level from a small electromagnetic interference (EMI) source. This kind of antenna is useful as a magnetic field probe for pre-compliance EMC measurements or debugging tasks since the user can scan a printed circuit board (PCB) looking for locations with strong magnetic fields. When a strong H-field point is found, the designer should check the PCB layout and components placement in that area to detect if this could result in an EMI source. This contribution focuses on analyzing the performance of an easy to build and low-cost H-field NFP designed and manufactured using a standard PCB stack-up. Thereby, the frequency range and sensitivity of the NFP-PCB are analyzed through a Finite Element Method (FEM) simulation model that makes it possible to evaluate its sensibility and effective frequency range. The numerical results obtained with the FEM models are validated against measurements to verify the design and performance of our NFP. The FEM model reproduces the experimental procedure, which is used to evaluate the performance of the NFP in terms of sensitivity by means of the simulated near-field distribution. The NFP-PCB has almost a flat response from 180 MHz to 6 GHz, with an almost perfect concordance between numerical and experimental S21 results. The numerical results show an average transmission loss of −27.9 dB by considering the flat response bandwidth, whereas the experimental one is −29.7 dB. Finally, the designed NFP is compared to two high-quality commercial probes in order to analyze its performance.

The reduction of embedded portable devices involves a magnetic field interference problem when it integrates near field communication (NFC) due to the presence of conductive surfaces, such as ground planes, batteries, or metallic enclosures. Flexible sintered ferrite sheets (FSFS) represent an interesting shielding solution to prevent electromagnetic interferences problems related to NFC, thanks to their ability to control the magnetic flux. The characterization of FSFS effectiveness is analyzed as a function of the sheet thickness in this contribution. This is performed with the aim of determining which is the optimum thickness value to retune an NFC antenna to its original operation frequency value (13.56 MHz) when it is affected by a near conductive surface. A finite element method simulation model is designed and corroborated with the experimental results to evaluate the performance of different FSFS thicknesses in terms of resonant frequency shift, magnetic field strength, and communication distance. An electromagnetic scanner is also used to determine the ability of the best FSFS thickness to shield an NFC transmitter antenna when a battery is set under it, emulating a usual problem. The results obtained show that the magnetic field strength is significantly attenuated and the communication distance is highly shorted. Therefore, besides selecting a material that provides high reflection and low losses at 13.56 MHz, thickness must be considered to ensure the greatest communication effectiveness. Consequently, the use of a wrong FSFS thickness could lead to shifting the resonance frequency to lower values than expected, detuning the communication.

Electromagnetic noise absorber sheets have become a solution for solving complex electromagnetic interference (EMI) problems due to their high magnetic losses. This contribution is focused on characterizing a novel structure that is based on an absorber film with a metal layer attached on its top side. Two different absorber compositions were combined with Al and Cu metal layers in order to study the improvement on the performance of these structures, depending on the complex permeability, absorber film thickness, and type of metal. The transmission attenuation power ratio of the absorber films is analyzed and compared to the performance of absorber and metal structures. The measurement procedure is carried out attaching the films into a microstrip line that has been designed based on IEC standard (IEC 62333-2). This test fixture is employed as a transmission line to simulate a general noise path. The performance of absorber composites to filter electromagnetic noise is evaluated through analyzing S₂₁ and S₁₁ parameters. This is carried out with the aim of finding out in which conditions the absorption loss is improved when a metal layer is attached. In addition, the possible re-radiation effect, due to the magnetic field that is generated by the eddy currents induced in the metal layer, is examined.

As the world continues to change and evolve, students must acquire a diverse set of competencies and skills that focus on sustainability. This term extends beyond environmental matters, encompassing educational aspects, such as critical thinking, communication, creativity, collaboration, and problem solving, all of which are crucial components. In order to promote these aspects in an engineering learning environment, using educational tools that emulate real-life tasks related to students’ future careers can significantly boost their motivation. It could be worth considering the integration of teaching techniques that align more closely with the professional work of engineering. By embracing this pedagogical approach, educators can empower students, contributing to the advancement of science and technology. The field of programming embedded or integrated systems presents numerous professional opportunities for students of Telecommunications and Electronics Engineering degrees. An embedded systems engineer is a specialized professional responsible for co-designing electronic devices based on a processor. This contribution analyzes the impact of introducing a mobile robot platform as a cutting-edge teaching approach that merges problem-based learning (PBL) with hands-on learning. The platform’s main features include robustness in reducing interconnection problems and the possibility of co-designing projects with multiple integrated sensors and actuators. This learning tool makes it possible for students to work with a professional embedded system that they can find in their future careers. Hence, assessing the impact of this learning strategy using the robot and how students perceive it to enhance their professional skills is fundamental. This evaluation compares students’ experiences in previous subjects with the learning approach proposed in this research that intends to support students to prepare them more effectively for transitioning to professional life. The evaluation involves a previous and post-questionnaire that examines three dimensions: energy, absorption, and dedication. Based on the findings, it can be concluded that the general satisfaction item showed the highest growth rate (1.05 out of 5.00) and the best score in the post-questionnaire. This indicates that, overall, the students evaluated the impact of using the learning strategy described positively. After completing the learning experience, the dimension of dedication showed the highest increase (0.73 out of 5.00) among all three dimensions.