Paul J. Shayler

Paul J. Shayler

Auto-generated profile, based on publicly available information

Paul J. Shayler

University of Nottingham

Research Focus & Metrics

Academic Career Length

45Years (1982-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 May 2013 in Tribology International
Verified
Journal Article
Closed access
Antonino La RoccaAntonino La Rocca
Antonino La Rocca
GLG. Di Liberto
G. Di Liberto
PSP.J. Shayler
P.J. Shayler
MFMichael Fay
Michael Fay

1 April 1993 in SAE International Journal of Advances and Current Practices in Mobility
Verified
Conference Paper
Closed access
PSP. J. Shayler
P. J. Shayler
SCS. J. Christian
S. J. Christian
TMT. Ma
T. Ma
A computational model has been developed to support investigations of temperature, heat flow and friction characteristics, particularly in connection with warm-up behaviour. A lumped capacity model of the engine block and head, empirically derived correlations for local heat transfer and friction losses, and oil and coolant circuit descriptions form the core of the model. Validation of the model and illustrative results are reported.

11 April 2005 in SAE International Journal of Advances and Current Practices in Mobility
Verified
Conference Paper
Closed access
PDF file
PSPaul J. Shayler
Paul J. Shayler
DLDavid K. W. Leong
David K. W. Leong
MMMichael Murphy
Michael Murphy
Friction data have been acquired from motored engine tests on four designs of light duty automotive diesel engines with a swept capacity around two litres (1.8l-2.2l). The data cover temperatures at the start of motoring of -20°C and above, and motoring speeds from 200 rev/min to 1000 rev/min. Most tests were carried out using SAE 10W/30 oil. The breakdowns separated piston assembly, crankshaft assembly, valve train and auxiliary component contributions to friction mean effective pressure (fmep). The empirical coefficients and functions used in the engine friction model developed by Patton, Nitschke and Heywood (SAE 890836) have been modified to fit the low speed, low temperature test data without greatly affecting predictions for fully-warm conditions. The dependence of component contributions on oil viscosity during warm-up has been taken into account.

1 February 2014 in Tribology International
Verified
Journal Article
Open access
Antonino La RoccaAntonino La Rocca
Antonino La Rocca
GLG. Di Liberto
G. Di Liberto
PSP.J. Shayler
P.J. Shayler
CPC.D.J. Parmenter
C.D.J. Parmenter
MFMichael Fay
Michael Fay
Nanoparticle Tracking Analysis (NTA) has been applied to characterising soot agglomerates of particles and compared with Transmission Electron Microscoscopy (TEM). Soot nanoparticles were extracted from used oil drawn from the sump of a light duty automotive diesel engine. The samples were prepared for analysis by diluting with heptane. Individual tracking of soot agglomerates allows for size distribution analysis. The size of soot was compared with length measurements of projected two-dimensional TEM images of agglomerates. Both the techniques show that soot-in-oil exists as agglomerates with average size of 120 nm. NTA is able to measure particles in polydisperse solutions and reports the size and volume distribution of soot-in-oil aggregates; it has the advantages of being fast and relatively low cost if compared with TEM

1 May 2014 in Applied Thermal Engineering
Verified
Journal Article
Closed access
WTWei Jet Thoo
Wei Jet Thoo
AKArman Kevric
Arman Kevric
HNHoon Kiat Ng
Hoon Kiat Ng
SGSuyin Gan
Suyin Gan
PSPaul Shayler
Paul Shayler
Antonino La RoccaAntonino La Rocca
Antonino La Rocca

1 January 2015 in Energy
Verified
Journal Article
Open access
JZJ.P. Zammit
J.P. Zammit
MMM.J. McGhee
M.J. McGhee
PSP.J. Shayler
P.J. Shayler
TLT. Law
T. Law
IPI. Pegg
I. Pegg
The influence of EIVC (early inlet valve closure) on emissions, fuel economy and exhaust gas temperature of a turbocharged, 4 cylinder common rail direct injection diesel engine has been investigated and compared with the influence of deactivating two cylinders. IVC (inlet valve closing) timings were set at up to 60 CA (crank angle) degrees earlier than the production setting of 37° ABDC for the engine. At the earliest timing, effective compression ratio was reduced from 15.2:1 to 13.7:1. The effects on emissions were significant only for EIVC settings at least 40 CA degrees earlier than the production setting, and were sensitive to engine load. At 2 bar BMEP (brake mean effective pressure) and fixed levels of NOx, soot emissions were reduced but CO (carbon monoxide) and HC (hydrocarbon) increased unless fuel rail pressure was reduced. With increasing load, soot reduction diminished and was negligible at 6 bar BMEP; CO and HC emissions deteriorated further. At all conditions, EIVC raised exhaust gas temperature by >50 °C; the effect on fuel economy was negligible or a fuel economy penalty. Comparisons indicate cylinder deactivation is the more effective strategy for reducing engine-out emissions of HC and CO and raising exhaust gas temperature under light load operating conditions