Michael Adams

Michael Adams

Auto-generated profile, based on publicly available information

Michael Adams

George W. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, GA 30332, USA

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
3 May 2019 in Physical Review Applied
Verified
Journal Article
Open access
PDF file
MAM.J. Adams
M.J. Adams
MVM. Verosky
M. Verosky
Mona ZebarjadiMona Zebarjadi
Mona Zebarjadi
JHJos Heremans
Jos Heremans
Active cooling systems use electrical work to bring a hot device (such as an integrated circuit) down to near ambient temperature by draining heat from the hot area of the device to a passive heat sink. Commercial thermoelectric modules are optimized for refrigeration, and are not ideal for active cooling. Refrigeration maintains a temperature that is below the ambient temperature in a device (such as a kitchen refrigerator) by pumping heat from the cold area of the device to a heat sink. The thermoelectric figure of merit zT is used traditionally to evaluate the performance of thermoelectric modules, including refrigeration modules. But it is not a good indicator of the performance of active cooling materials. Here, we describe an efficient, all-solid-state active cooler based on the Peltier effect in metals with high thermoelectric power factor due to electron correlation effects (CePd3) or magnon drag (Co) and high passive thermal conductivity. We show theoretically and experimentally that the effective thermal conductance under applied current can exceed the limits imposed by Fourier’s heat conduction law. The designed device measures an effective thermal conductance that is an order of magnitude larger than the passive thermal conductance at ΔT = 1 K with the dynamic response of 4 s.

13 May 2024 in Solar Energy
Verified
Journal Article
Open access
KHKyu Bum Han
Kyu Bum Han
EJEunjin Jeon
Eunjin Jeon
PDPatrick Davenport
Patrick Davenport
JSJason Schirck
Jason Schirck
MAMichael Adams
Michael Adams
ZMZhiwen Ma
Zhiwen Ma

9 December 2025 in Chemical Communications
Verified
Journal Article
Open access
PDF file
MAMichael J. Adams
Michael J. Adams
TKTae Kyu Kim
Tae Kyu Kim
SPSamuel Pennell
Samuel Pennell
Judith VidalJudith Vidal
Judith Vidal
AMAkanksha K. Menon
Akanksha K. Menon
Comparative analysis of cycling-induced degradation in thermochemical energy storage materials is standardized by implementing a general rate model.

11 March 2026 in SSRN Electronic Journal
Verified
Preprint
Open access
AMAkanksha Menon
Akanksha Menon
MMMadeline R. Morrell
Madeline R. Morrell
MAMichael Adams
Michael Adams
MPMia Pomilia
Mia Pomilia
Salt hydrates are promising thermochemical materials for thermal energy storage in buildings due to their high energy density, reaction temperatures, and negligible self-discharge during storage. While most efforts have characterized the properties of powder samples, their realistic application in packed bed reactors necessitates understanding the behavior of densified form factors, i.e., pellets. To address this gap, this work evaluates the key thermophysical properties that impact coupled heat and mass transport in pellets of four salt hydrates: SrBr2, SrCl2, K2CO3, and MgSO4. First, the reaction advancement was compared for powders versus pellets, which revealed the effect of intra-particle diffusion resistance (transport limited). Next, effective water vapor diffusion coefficients were characterized via a wet-cup analysis, and thermal diffusivities were measured via laser flash analysis for pellet densities from 82% to 94% (corresponding porosities from 18% to 6%). Vapor diffusion coefficients decreased with pellet density ranging from 0.3-2.5 mm2/s, while thermal diffusivities increased with pellet density ranging from 0.2-0.33 mm2/s. Using this and specific heat values from literature, thermal conductivities were calculated to be between 0.35-0.80 W/m-K for the different hydrated salts. Finally, the Lewis number was used to show that pristine hydrated salt pellets in an open system are heat transport limited, however the evolution of these properties with cycling must be considered to fully understand their coupled thermo-chemo-mechanical behavior.

9 February 2023 in Journal of Applied Physics
Verified
Journal Article
Open access
PDF file
MAMichael J. Adams
Michael J. Adams
SYShannon K. Yee
Shannon K. Yee
The switching ratio of a thermal switch is a key design parameter, and electrically activated switches based on thermoelectric effects have been reported to produce large switching ratios over a wide range of temperatures. Previous switches based on the Seebeck effect have switching ratios that are limited by the thermoelectric figure-of-merit zT. Perhaps, more importantly, they are limited by their device construction of alternating p-type and n-type materials with soldered junctions. Alternatively, we show that semiconducting polymers with spatially graded doping can offer similar switching ratios due to a volumetric heat absorption effect. This occurs in heavily doped polymers, which exhibit a sharp decrease in the Seebeck coefficient as charge carriers become fully delocalized. Such heat absorption is analogous to the Thomson effect, where heat is locally absorbed due to temperature-dependent variation of the Seebeck coefficient. Here, a theoretical model is derived to solve the 1D heat equation with spatially graded doping, allowing for optimization of the doping profile for a given material system. Four different material systems are compared according to an analysis of reported measurements to determine the upper limit of the switching ratio. A hypothetical Thomson switch based on poly(3,4-ethylenedioxythiophene) doped with ferric tosylate can produce switching ratios up to 12 under a thermal bias of 10 K, a threefold increase compared to a Peltier switch of the same material. Like a Peltier switch, the switching ratio of a Thomson switch diverges under a small thermal bias. Under a large thermal bias, the switching ratio converges toward that of an equivalent Peltier switch.

22 July 2024
Verified
Report
Open access
PDF file
SYShannon Yee
Shannon Yee
MAMichael Adams
Michael Adams
The goal of this project is to gather thermophysical property data – specifically, thermal conductivity, thermal diffusivity, and specific heat – of heat transfer media (HTMs) and containment materials (CMs) used in Topic Area 1 and 2A at high temperatures (>700°C). This goal was met by completing objectives such as qualifying high temperature measurement techniques, defining allowable uncertainty metrics, reporting properties in a public database, and providing ongoing support for prioritized materials. These are described in detail across three budget periods