1 March 2020 in Journal of Photochemistry and Photobiology A: Chemistry
13 August 2020 in Journal of Chemistry
This study investigates the possibility of applying an adsorption process using two abundant natural minerals M1 and M2. Without pretreatment or activation, the adsorbents were used to treat real textile wastewater samples (collected from Fez city, Morocco). As a cost-effective alternative, these materials were characterized by different analyses, including X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), and X-ray fluorescence (XRF). Chemical oxygen demand (COD) and biological oxygen demand (BOD) were used to characterize the textile wastewater. Additionally, the influence of operating conditions (contact time, adsorbent dosages, and pH) was evaluated. Results show that the adsorption process takes place quickly, reaching the equilibrium at 90 and 160 min for M1 (88% COD) and M2 (79% COD). Both materials show a higher affinity to Cr (39%) and lower affinity to Cu (28%). A pseudo-second-order kinetic model provides the best fit to the experimental adsorption data. Germination tests indicate a low toxicity after the adsorption process. Performance of both materials was compared with that of other literature studies.
8 October 2020 in Journal of Chemistry
In this work, the adsorption of Remazol Brilliant Blue (RBB) over raw date pits (RDPs) as an inexpensive adsorbent has been examined. In addition, all parameters such as the adsorbent mass, solution pH, RDP particle size, RBB initial concentration, and temperature on the adsorption of RBB influencing the adsorption procedure were studied to provide fundamental information of the adsorption equilibrium. The characterization of RDP material is investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), and Fourier-transform infrared spectroscopy (FTIR). Based on the calculation, the kinetic rate of the adsorption was well modeled by pseudo-second-order and Langmuir isotherm. Surface functional groups of RDP have substantially been influenced by the adsorption characteristics of RBB. The capacity of the adsorption has achieved 105 mg/g and a removal efficiency of 90.4% at 1.5 g/L RDP mass, 40 mg/L initial dye concentration, pH 2, temperature of 328 K, 40 µm particle size, and contact time of 50 min. The capacity of the adsorption could reach 198 mg/g by increasing the ionic strength of RBB solution. Desorption tests showed that RDP adsorbent has the disadvantage of losing efficiency while reusing for many cycles. However, it still abundant and inexpensive. Therefore, RDP can be used as a potential low-cost bioabsorbent for the elimination of RBB from wastewater.
1 June 2021 in Nano Futures
This work reports a key factor, the H 2 SO 4 concentration, in controlling the physicochemical properties of titanium dioxide (TiO 2 ) photocatalysts during the sol–gel synthesis. The photocatalysts synthesized using different concentrations of H 2 SO 4 possess specific anatase/rutile ratios and crystallite sizes as well as surface areas, resulting in different photocatalytic performance in the degradation of formic acid in solution. The best photocatalytic performance is observed for the TiO 2 photocatalyst containing a relatively high percentage of the rutile phase (∼84%), which is obtained from the sol–gel synthesis without H 2 SO 4 .
1 March 2021 in Sensors and Actuators A: Physical
1 January 2021 in Heliyon
Copper and nickel were incorporated into the prepared yellow clay (YC) using one of the most widely used methods, for the preparation of heterogeneous catalysts, which is the wet impregnation method (IPM) and its application as a heterogeneous catalyst for Caffeine (CAF). Several catalysts Cooper Nickel's Catalysts (Cu–Ni) were applied to the yellow clay with different weight ratio of Cu and Ni, in order to explore the role of both metals during the catalytic oxidation process CWPO. Furthermore, the CuNi-YC catalysts, were characterized by X-ray diffraction (XRD), X-ray fluorescence (XRF), Langmuir's surface area, Brunauer Emmett Teller (BET), scanning electron microscope (SEM) and inductively Coupled Plasma-Atomic Emission Spectrometry (ICP-AES), so as to get a better understanding concerning the catalytic activity's behavior of CuNi-YC catalysts. The optimization of the catalytic activity's effects on the different weight ratios of Cu and Ni, temperature and H2O2 were also examined, using Box-Behnken Response Surface Methodology RSM to enhance the CAF conversion. The analysis of variances (ANOVA) demonstrates that Box-Behnken model was valid and the CAF conversion reached 86.16%, when H2O2 dosage was equal to 0.15 mol.L−1, copper impregnated (10%) and temperature value attained 60 °C. In addition, the regeneration of catalyst's cycles under the optimum conditions, indicated the higher stability up to four cycles without a considerable reduction in its conversion performance.