29 March 2024 in EUREKA: Physics and Engineering
Despite the fact that a large amount of small arms ammunition has been used up over the past two years, their stocks in warehouses and arsenals in various countries are quite large. And their shelf life is 20 years or more. In addition, over time, the number of such ammunition will increase. Among the large number of requirements for modern small arms, one can highlight the provision of the necessary survivability of its parts and mechanisms. The problem of barrel survivability is especially important. One of the factors affecting barrel survivability is changes in internal ballistics parameters. In turn, these parameters change when using ammunition whose service life exceeds the warranty. In this regard, the task of studying the survivability indicators of small arms barrels when using post-warranty ammunition seems relevant. The requirements for barrel systems and factors affecting the wear of the barrel bore of powder charges during long-term storage have been determined. An analysis of changes in the ballistic characteristics of powder charges was carried out, which allows to state increased wear of barrels when using ammunition with long storage periods. The dependencies for determining the limit number of shots from a weapon sample are analyzed. A method for predicting barrel survivability when using long-term storage ammunition is proposed. Data are presented on an experimental study to determine changes in barrel survivability as a result of the use of long-term storage ammunition by estimating changes in the initial velocity of the projectile. Based on the results obtained, ways for further research are proposed in the direction of expanding the range of ammunition and weapons
29 September 2023 in EUREKA: Physics and Engineering
World experience in storing ammunition shows that during long-term storage, pyroxylin gunpowders used in ammunition are capable of arbitrarily undergoing various physical and chemical transformations, which negatively affects the ballistic characteristics of ammunition. In some countries, ammunition is in use with a shelf life of 30–35 years or more. Factors influencing the physicochemical stability of gunpowder charges during long-term storage have been identified. An analysis of the chemical processes occurring in nitrocellulose gunpowders (NCP) during long-term storage is carried out, and the possibility of regenerating NCP by treatment with hydrogen peroxide is substantiated. It is indicated that there are no methods for regenerating gunpowder charges with long shelf life. It has been shown that one of the ways to increase the ballistic and energy characteristics of long-term storage ammunition can be the regeneration of nitrocellulose gunpowder charges. Data are presented on an experimental study to determine the characteristics of NCP after regeneration. It has been shown that when regenerating nitrocellulose gunpowder charges with hydrogen peroxide, the calorific value of the starting material increases. Based on the results obtained, an approach to assessing the feasibility of using regeneration technology is proposed. This approach is based on the effect of mass replenishment during the regeneration process due to ongoing chemical processes and heat and mass transfer. The ways for further research on the use of nitrocellulose as a high-calorie fuel are presented
25 May 2023 in EUREKA: Physics and Engineering
There is a need for vehicles to maneuver when there are traffic jams, to overcome narrow streets and various obstacles. This leads to increased requirements for dynamism and maneuverability of vehicles. The authors present the results of the development and research of the steering control of the vehicle, which provides increased maneuverability. Such circumstances significantly affect the increase in maneuverability of wheeled vehicles, including tractors, for which the use of front suspension axles is possible in terms of layout. The use of a front swing axle with electric motor-wheels with separate control will increase the maneuverability of a two-axle vehicle and minimize the steering effort when turning. When solving the task, a mathematical model of the movement of the vehicle on a turn was created. The forces in the contact of the wheels with the road surface were determined, which made it possible to determine the forces and moments of resistance to the rotation of the front axle. Rational laws of control of turning the front axle, providing minimal resistance to the movement of the vehicle, were obtained. A vehicle turning control option is proposed, in which the wheels of the outer and inner sides are alternately braked when the vehicle enters and exits the turn. In addition, it is possible to alternately create a torque difference on the wheels of the outer and inner sides of the front axle. Using the proposed turn control options, it is possible to create a multi-axle vehicle with a rocking axle. The materials of the article on the controllability of vehicles depending on the design of the steering and front axle are of interest to researchers, designers of mobile equipment, graduate students and students of engineering specialties
7 June 2023 in Bulletin of the National Technical University «KhPI» Series: Engineering and CAD
A large number of scientific works and design developments are devoted to the study and improvement of the properties of maneuverability, which is also a complex (complex) property. At one time, the need to reduce the building volume required the installation of swivel wheels on the front steering axle of the car. However, in this case, additional resistance to the movement of the machine arose, which is due to the discrepancy between the trajectories of the movement of the front outer and inner guide wheels with their trajectories during an ideal turn. The development of the designs of electric vehicles and hybrid vehicles allows for separate control of the front wheels. The analysis of the whole variety of indicators and criteria of maneuverability in general and individual properties was carried out. Unlike other systematization of these indicators and criteria, it is proposed to divide these indicators and criteria into three main groups. All indicators and criteria used to assess the maneuverability of vehicles are also used to assess the maneuverability of wheeled tractors with a center of mass shifted to the rear axle and, therefore, have low controllability. Force and energy criteria can be used in the design of cars and tractors to ensure the ability of the latter to maneuver. In addition, as a result of the study, a combined method for controlling the movement of a two-axle swivel bogie of a wheeled vehicle has been improved due to the fact that its rotation is carried out by two torque control moments. The first of these control torques is generated by the driver through the steering and power cylinder. The second torque control moment is created due to the difference in torques on the wheels of the outer and inner sides of the two-axle swivel bogie. The implementation of these rules for regulating the distribution of traction forces between the sides makes it possible to overcome the resistance to rotation of a two-axle swivel bogie and improve the quality of motion control of the specified bogie and wheeled vehicle. Keywords: maneuverability, separate control, wheeled vehicle, control method, two-axle swivel bogie
9 April 2025 in Випробування та сертифікація
The use of a Luneberg lens allows you to significantly increase the effective scattering surface of unmanned aerial vehicles, thus simulating more significant targets. This effect is achieved by smoothly decreasing the dielectric constant from the center of the lens to its edge. It is quite difficult to manufacture a classic Luneberg lens with a continuous law of change of the dielectric constant (refractive index) along its radius. In practice, to ensure a decrease in the dielectric constant of a spherical Luneberg lens as its radius increases, they switch to a stepwise approximation of the law of change of the dielectric constant using a multilayer lens design. The technical implementation of a multilayer spherical Luneberg lens is carried out by dividing it into layers with different dielectric constants, which increase from the outer radius of the sphere to the center. Within one layer, the dielectric constant remains constant. To implement the stepwise approximation of the law of change of dielectric permittivity, various methods of layer-by-layer approximation of the body of a spherical Luneberg lens are used. The following methods of dividing the lens into layers are possible: uniform division by refractive index; uniform division by dielectric permittivity; uniform division by radius. A method of layer-by-layer approximation is proposed for different methods of dividing the lens into layers and algorithms are presented. The average absolute error of approximation is chosen as the criterion for the effectiveness of the approximation of the stepwise approximation of the law of change of dielectric permittivity to the theoretical one. The conducted studies have shown that the best approximation of the dielectric permittivity to the theoretical law of change is ensured by uniformly dividing the Luneberg lens into layers by radius. For a six-layer spherical Luneberg lens, the absolute error in the approximation of the dielectric constant to the theoretical value with a uniform distribution along the radius is no more than 0.0663 (6.7%).
13 September 2021 in EUREKA: Physics and Engineering
Emergency prevention is based on analysis, forecasting and early response to emergencies. A systematic approach to solving the problem of preventing emergencies envisages forecasting emergencies by type, level and possible losses caused as a their results both in the state as a whole and in its regions. To implement a systematic approach based on a formalized mathematical model, an organizational and technical method has been developed for predicting emergencies and possible losses caused as their results. The method is a combination of a variable order polynomial regression method, a weighted least squares method, and a probabilistic statistical method. This allows to compensate for the shortcomings of some at the expense of others, which will lead to an increase in forecasting accuracy. A control algorithm has been developed for the implementation of an organizational and technical method for predicting emergency situations and possible losses caused as their results. Its use involves the implementation of a number of interrelated procedures. At the first stage, the collection, processing and analysis of information on emergency situations in the country for a certain period of monitoring is carried out. This is the basis for predicting the processes of emergencies in general, in nature, level and types, as well as losses due to them both in the state and its regions. The information received is taken into account when forming a decision on the actions of civil protection units in order to adequately respond to emergency situations and eliminate their consequences. Based on the analysis of the effectiveness of the actions of the response units, the decisions on the elimination of emergency situations are adjusted. The developed method makes it possible to reasonably approach the planning and implementation of organizational and technical measures to prevent emergency situations, taking into account the potential threats to the territories and population of the country's regions