State Key Laboratory of Material Processing and Die & Mould Technology, School of Materials Science and Engineering, Huazhong University of Science and Technology 1 , Wuhan 430074
Auto-generated profile, based on publicly available information
Boyuan Di
State Key Laboratory of Material Processing and Die & Mould Technology, School of Materials Science and Engineering, Huazhong University of Science and Technology 1 , Wuhan 430074
We demonstrated that the carrier polarity of MoTe2 transistors can be modulated by controlling the channel thickness with NiTe2 semimetal contacts. The multilayer MoTe2 transistors (thickness >7.1 nm) exhibit a symmetric ambipolar conduction, and a transition to unipolar p-type polarity occurs as the channel thickness decreased down to ∼2.3 nm. The position of the semimetal NiTe2 work function was verified to be located at the mid-gap of multilayer MoTe2, and the observed transition was interpreted by a synergistic effect of the channel thickness-dependent band alignment and charge transfer behavior with unique NiTe2 semimetal contacts.
We present a Ge/MoS2 van der Waals heterojunction photodetector with a short active region constructed using a transfer process. The device exhibits broadband, self-powered, superior device performance within the visible to infrared wavelength (500–1700 nm) operated in a photovoltaic mode. Intriguingly, a sharp increased gain of 10 556 (93) with a varied breakdown voltage of −8.02 V (−6.25 V) under the 700 nm (1550 nm) laser illumination was observed, which was interpreted as the synergistic effect of both soft and avalanche breakdown behavior. These results imply disposable high-sensitivity broadband light-detection potentials with a simple Ge/MoS2 heterojunction, exempting it from the complex and strict construction requirement of conventional avalanche photodetectors.
We demonstrated that ternary HfAlO2 amorphous film prepared with common co-sputtering technology can be a suitable gate dielectric for bilayer MoTe2 transistors. The film quality can be improved by optimizing the sputtering process and post-annealing treatment, which is superior to its binary Al2O3 and HfO2 components and satisfies gate dielectric criteria. The bilayer MoTe2 transistors with ∼29-nm-thick HfAlO2 gate dielectric exhibit an Ion/Ioff ratio of over 108 by a low operating voltage, together with a small subthreshold swing ≈ 71.22 mV/dec. These promising characteristics favor the development of high-performance and low-power ultrathin MoTe2-based beyond-silicon electronics.
We have clarified the impact of process control on the electrical breakdown characteristics of quasi-one-dimensional ZrTe3 interconnects. The regulation of contact resistance by process control enables significant variance of both breakdown current density and structural characteristics. The ZrTe3 interconnects fabricated with a conventional photolithography process show high contact resistance, low breakdown current density, and electromigration-dominated structural breakdown characteristics. By supplementing a reactive ion etching step to reduce contact resistance, the breakdown current density and structural characteristics change significantly. Further contact resistance reduction by adopting a transfer process promotes significantly increased breakdown current density and distinct thermal decomposition-dominated structural characteristics. The current investigation implies that the process control is crucial for quasi-one-dimensional ZrTe3 interconnects.
We demonstrate that homogeneous MoTe2 complementary metal–oxide–semiconductor (CMOS) inverters can be constructed through a simple work function engineering strategy using van der Waals contacts. Polarity control of MoTe2 transistors is achieved by employing high-work function degenerated semiconductor SnSe2 and low-work function semimetal Bi as source/drain electrodes for p-type and n-type operation, respectively. Both types of transistors operate in enhance-mode and exhibit on/off current ratios exceeding 106. The resulting homogeneous MoTe2 CMOS inverter, incorporating an h-BN flake as the gate dielectric, achieves a high voltage gain of 78 at a supply voltage of 4 V. These results highlight the potential of this simplified device architecture for realizing high-performance homogeneous MoTe2 CMOS logic circuits.
We have demonstrated series ternary HfSe2(1-x)Te2x single crystalline alloys can be synthesized by a general chemical vapor transport approach. These alloys were verified to exhibit composition-dependent bandgap tunability (from 1.1 to 0 eV) by growth process control. Such characteristic offers a feasible way to construct HfSe2(1-x)Te2x alloy channel transistors using Dirac semimetal HfTe2 as contact electrodes, which shows negligible Schottky barrier height. Notably, the HfSe1.8Te0.2 channel transistor with a channel length of 9.48 μm on a 14 nm h-BN dielectric achieves a balance performance with current Ion/Ioff ratio of 9.5 × 104 and an Ion of 0.828 μA/μm. The current investigation of alloy engineering offers a feasible way of developing high-performance HfSe2-based beyond-silicon electronics.