10 September 2018 in IEEE Journal of Radio Frequency Identification
Screen printing is a stencil process where conductive inks are patterned onto substrates through a fine mesh of threads. Nowadays, screen printing can be used to print RFID antenna structures onto flexible and ultra-low-cost substrates such as paper. In this manuscript, we present an HF RFID reader antenna system, operating at 13.56 MHz, using screen printed Ag particle ink as conductor and using HP photo paper as substrate. The pro-posed antenna system comprises four loop antenna elements, matched to 50Ω, and one I2C addressed SP4T multiplexer circuitry, controlled through an exterior embedded system. The geometries, designs and characterizations of the antenna system are described in the manuscript in details. Measurement results show that the antenna system has low power reflections and a suitable Q factor. It has a maximum 11.1 cm RFID tag read range at an antenna system input power of 33 dBm. 2D RFID tag positioning can be enabled by utilizing the RFID tag interrogation zones formed by the four loop antenna elements. In addition, a parametrical study is carried out to investigate the effect of loop antenna element DC resistance on the antenna element performance. It can be concluded that the proposed method can be used to create low-cost and large-area HF RFID reader antenna systems.
26 January 2018 in Flexible and Printed Electronics
The development of printed electronics on flexible substrates is increasing rapidly, where the main benefits are the large area and low cost. However, the functionality and performance of printed circuits cannot compete with standard silicon based microprocessors or integrated circuits, though the functionality and performance of printed circuits are increasing. Therefore, in this work we investigate the possibilities of using Sn42/Bi57.6/Ag0.4 low-temperature solder paste together with a reflow solder oven and hot air solder iron to mount regular surface mount device (SMD) components on screen-printed silver tracks. It was found that it is possible to solder standard Si SMD packages onto screen-printed Ag ink tracks on paper substrate; however, the component bonding strength to polyimide was not satisfactory. The resistance of the solder joints was found to be no more than 240 mΩ. The bond strength was found to be higher using the manual hot air solder iron than the reflow solder oven. Bending tests show that the bonding strength is higher for the hot air soldered components. Reference samples on FR-4 based copper printed circuit board show a bond strength ∼10 times higher but we conclude that it is possible to solder regular Si SMD components onto Ag-printed conductors on paper substrate with good results. The process could be used to fabricate hybrid printed electronics in a standard solder process line.
1 December 2019 in Flexible and Printed Electronics
Implementing electronics systems on paper is an important area of flexible circuit technologies. One of the approaches is to print conductive inks onto paper substrates, on which silicon-based surface mount device components are mounted. However, one of the problems is that the printed conductors have unneglectable resistivity. In this paper, we present paper-based flexible circuits, using copper and aluminium conductors that are laminated onto paper substrates using a high-speed roll-to-roll method. Edge roughness inspections and repeated two-point bending tests are carried out to evaluate the manufactured flexible circuits. Three surface mount techniques are used to assemble standard surface mount device components onto the flexible circuits, including an isotropic conductive adhesive, an anisotropic conductive adhesive, and a low-temperature solder paste. Several characterizations are performed to the surface mount techniques, including contact resistance measurements, component bonding strength tests, assembled circuit bending tests, and scanning electron microscopy. The results of the characterizations suggest that flexible circuits made from Cu with paper substrate achieve satisfactory results for mechanical reliability, all surface mount techniques, and have the potential to be used on automatic component assembly lines. In order to test whether such flexible circuits and surface mount techniques can be used in implementing electronics systems, passive NFC tags with relative humidity sensing functionality are made, which are interrogated by an NFC equipped mobile phone.
31 January 2018 in Flexible and Printed Electronics
RF electronics commonly incorporate PCB materials with low loss tangents, which limits its use for large-area applications due to its high cost. This work verifies one alternative solution how non-conventional flexible circuit materials can be used to manufacture large functional surfaces for RF-based applications. Laminated Al foils are used for conducting layers and a flexible foam material is used for substrate. An RFID reader system has been developed to demonstrate the functionality, comprising of eight microstrip antenna elements arranged in a SP4T switching structure covering an area of 1.2 m × 0.6 m. Each antenna element is individually addressable with aid of distributed digital and analogue multiplexer circuitry and it is shown how these components can be soldered directly onto the Al conductors. The constructed system shows good RF performance, both with regards to the materials and to the interconnections with the distributed multiplexer circuitry. It can perform far-field RFID tag reading above its surface without dead zones and the system characterization implies that the concept can be further expanded to cover geometrical areas up to 1000 square meters.