1 June 2013 in Sensors and Actuators B: Chemical
19 November 2015 in Nanotechnology
Current nanostructure fabrication by etching is usually limited to planar structures as they are defined by a planar mask. The realization of three-dimensional (3D) nanostructures by etching requires technologies beyond planar masks. We present a method for fabricating a 3D mask that allows one to etch three-dimensional monolithic nanostructures using only CMOS-compatible processes. The mask is written in a hard-mask layer that is deposited on two adjacent inclined surfaces of a Si wafer. By projecting in a single step two different 2D patterns within one 3D mask on the two inclined surfaces, the mutual alignment between the patterns is ensured. Thereby after the mask pattern is defined, the etching of deep pores in two oblique directions yields a three-dimensional structure in Si. As a proof of concept we demonstrate 3D mask fabrication for three-dimensional diamond-like photonic band gap crystals in silicon. The fabricated crystals reveal a broad stop gap in optical reflectivity measurements. We propose how 3D nanostructures with five different Bravais lattices can be realized, namely cubic, tetragonal, orthorhombic, monoclinic and hexagonal, and demonstrate a mask for a 3D hexagonal crystal. We also demonstrate the mask for a diamond-structure crystal with a 3D array of cavities. In general, the 2D patterns on the different surfaces can be completely independently structured and still be in perfect mutual alignment. Indeed, we observe an alignment accuracy of better than 3.0 nm between the 2D mask patterns on the inclined surfaces, which permits one to etch well-defined monolithic 3D nanostructures.
30 April 2011 in Thin Solid Films
1 January 2011 in Procedia Engineering
Inversion of nanocrystalline ZnO(Ga) sensor signal during ammonia detection is reported for the first time. In the middle temperature region (250-300°C) the presence of ammonia in air results in increase of resistance. Comparative EPR study and dc conductance measurements allows to attribute this effect to changes in donor and acceptor defect concentration
27 October 2026 in Nanotechnology
State-of-the-art integrated circuits currently involve multi-layered architectures that rapidly extend towards three-dimensional (3D) semiconductor structures. To overcome out-of-plane alignment issues, we present an original method to employ conventional deep-UV lithography on pre-structured silicon substrates to pattern an etch mask for monolithic 3D nanostructures with N layers using only M = 1 overlay alignment step (instead of M = (N - 1) steps as in layer-by-layer assembly). The target nanostructures studied here consist of arrays of pores that intersect at oblique angles. To this end, we project elliptical apertures on the sidewalls of V-trenches at controllable depths relative to the wafer's top surface. We create V-trenches in Si by hot HF 50% and KOH 25% etching with θ = 54.7° sloping sidewalls. We successfully spin-coat photoresist on the sloping V-trench sidewalls with a thickness between 50 and 800 nm. The photoresist is remarkably homogeneous, better than 4 nm along 2.6μm of the V-trench sidewall. Using a single deep-UV lithography exposure at λ= 193nm (with a 25 mJ/cm 2 dose and a nominal focal plane at 500 nm depth below the Si wafer top-surface) we successfully expose apertures at various depths in the photoresist on sloping sidewall surfaces of the V-trenches. The apertures have diameters between d = 180 nm and 509 nm, to as deep as Z = 1180nm below the wafer surface. We develop an analytical model to successfully describe lithographic exposure on an inclined surface, which allows one to sculpt non-planar aperture arrays on inclined surfaces. In the future, aperture arrays on inclined surfaces may serve as etch masks to create monolithic and controllable 3D nanostructures deep inside silicon with a reduced number of overlay alignment steps, thus increasing the yield and throughput, and reducing costs and use of chemical and material resources.