Yitzchak S. Rosen

Yitzchak S. Rosen

Auto-generated profile, based on publicly available information

Yitzchak S. Rosen

Casali Center of Applied Chemistry, Institute of Chemistry, The Hebrew University of Jerusalem, Jerusalem 91904, Israel

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 December 2017 in ACS Applied Materials & Interfaces
Verified
Journal Article
Closed access
NANina Armon
Nina Armon
EGEhud Greenberg
Ehud Greenberg
MLMichael Layani
Michael Layani
YRYitzchak S. Rosen
Yitzchak S. Rosen
Shlomo MagdassiShlomo Magdassi
Shlomo Magdassi
HSHagay Shpaisman
Hagay Shpaisman

16 February 2017 in ACS Omega
Verified
Journal Article
Open access
YRYitzchak S. Rosen
Yitzchak S. Rosen
AYAlexey Yakushenko
Alexey Yakushenko
AOAndreas Offenhäusser
Andreas Offenhäusser
Shlomo MagdassiShlomo Magdassi
Shlomo Magdassi
Printing conducting copper interconnections on plastic substrates is of growing interest in the field of printed electronics. Photonic curing of copper inks with intense pulsed light (IPL) is a promising process as it is very fast and thus can be incorporated in roll-to-roll production. We report on using IPL for obtaining conductive patterns from inks composed of submicron particles of copper formate, a copper precursor that has a self-reduction property. Decomposition of copper formate can be performed by IPL and is affected both by the mode of energy application and the properties of the printed precursor layer. The energy application mode was controlled by altering three pulse parameters: duration, intensity, and repetitions at 1 Hz. As the decomposition results from energy transfer via light absorption, carbon nanotubes (CNTs) were added to the ink to increase the absorbance. We show that there is a strict set of IPL parameters necessary to obtain conductive copper patterns. Finally, we show that by adding as little as 0.5 wt % single-wall CNTs to the ink the absorptance was enhanced by about 50% and the threshold energy required to obtain a conductive pattern decreased by ∼25%. These results have major implications for tailoring inks intended for IPL processing.

25 October 2018 in Advanced Materials Technologies
Verified
Journal Article
Closed access
PDF file
YRYitzchak Rosen
Yitzchak Rosen
RMRoy Marrach
Roy Marrach
VGVitaly Gutkin
Vitaly Gutkin
Shlomo MagdassiShlomo Magdassi
Shlomo Magdassi

22 December 2014 in Advanced Materials Interfaces
Verified
Journal Article
Closed access
PDF file
YRYitzchak Rosen
Yitzchak Rosen
MGMichael Grouchko
Michael Grouchko
Shlomo MagdassiShlomo Magdassi
Shlomo Magdassi

31 March 2020 in ACS Applied Energy Materials
Verified
Journal Article
Closed access
VSViviana Sousa
Viviana Sousa
BGBruna F. Gonçalves
Bruna F. Gonçalves
YRYitzchak S. Rosen
Yitzchak S. Rosen
JVJosé Virtuoso
José Virtuoso
PAPedro Anacleto
Pedro Anacleto
YKYury V. Kolen'Ko
Yury V. Kolen'Ko

1 September 2017 in Flexible and Printed Electronics
Verified
Journal Article
Closed access
PDF file
YRYitzchak S Rosen
Yitzchak S Rosen
YLYuval Lidor
Yuval Lidor
RBRevital Balter
Revital Balter
ASAdi Szeskin
Adi Szeskin
AAAsad Awadallah
Asad Awadallah
Shlomo MagdassiShlomo Magdassi
Shlomo Magdassi
We present a novel process to fabricate conductive patterns by a new copper precursor ink. In this method, an ink with copper formate, a self-reducible copper precursor, is printed, and subsequently heated under high pressure in a hot-press, which is commonly used in the printed circuit board industry. The heating leads to decomposition of the precursor, and results in copper patterns with good electrical conductivity. The application of pressure enables the formation of a dense copper film. 5–15 μm thick copper patterns were obtained on FR4 sheets with an equivalent specific resistivity as low as 5.3 ± 0.3 μΩ cm, which is about three times the copper bulk resistivity. Unlike most methods for copper precursor inks, this ink and process do not require an inert environment, and can be performed with instrumentation already used in the industry. Finally, we demonstrate the applicability of this method by printing functional radio frequency components; i.e. antennas for near field communication and Wi-Fi.