5 November 2014 in IEEE Transactions on Plasma Science
We describe magnetohydrodynamic power generation experiments with seed-free high-temperature inert gas plasma using a linear-shaped Faraday-type generator driven by a shock-tunnel facility. The influence of inlet total temperature between 6500 and 9000 K on the plasma characteristics and its influence on generator performance are shown. By increasing the inlet total temperature, streaky and unstable plasma, characterized by large fluctuations in power output, is transformed into homogeneous and stable plasma, providing stabilized and improved power output. A quasi-1-D numerical simulation suggests that the plasma in the generator undergoes recombination when the inlet total temperature is high, which might be a factor in plasma stabilization. At the optimum load resistance, the enthalpy extraction ratio is improved to 12.9%; the optimum load resistance decreases as inlet total temperature is increased by the increase in electrical conductivity.
31 January 2017 in IEEE Transactions on Plasma Science
In a seed-free inert-gas disk-shaped magnetohydrodynamic (MHD) generator, the effect of the self-excited Joule heating in the nozzle region on the generator performance has been examined with 2-D r-z numerical simulations. The working gas (pure inert gas) can be ionized efficiently with the assistance of the self-excited Joule heating in the nozzle located upstream of the generator channel, even for a small, externally applied preionization power (PP). The increase in the ionization degree in the nozzle and the decrease in the optimum electrical conductivity in the generator channel with increase in the magnetic flux density reduce the optimum PP that maximizes the net enthalpy extraction (EE) ratio. For a typical argon disk MHD generator, a maximum net EE ratio of 25% and an isentropic efficiency of 65% can be obtained at a small PP of 0.3% of the inflow enthalpy under a magnetic flux density of 4 T. The enhancement of the ionization degree in the nozzle and the inhomogeneity of the plasma in the vertical direction because of the current concentration near the anode edge are more marked for argon and xenon, with their higher ionization rates, than for helium.
1 January 1992 in Review of Scientific Instruments
19 May 2016 in IEEE Transactions on Plasma Science
Magnetohydrodynamic power generation experiments with seed-free pure xenon plasma have been conducted using a shock tunnel. The effects of inlet total temperatures between 5000 and 11 500 K and magnetic flux density on the generator performance and plasma characteristics are revealed. An enthalpy extraction ratio of 4.1% is achieved at an inlet total temperature of 6000 K, which is higher than that for argon at the same inlet total temperature. The enthalpy extraction ratio increases with increasing inlet total temperature and magnetic flux density, but saturates at a high inlet total temperature (>8000 K). The inhomogeneous and unstable plasma due to ionization instability at a low inlet total temperature changes to a homogeneous and stable state with an increase in the inlet total temperature. The change in plasma structure occurs at a temperature between 6500 and 7000 K, which is lower than that in the case of argon. Moreover, plasma stabilization is achieved at a low magnetic flux density even when the inlet total temperature is low.
1 March 2025 in Journal of Propulsion and Power
The power generation characteristics of a disk-shaped magnetohydrodynamic generator driven by rotating detonation with potassium-seeded hydrogen–air mixture are examined via quasi-two-dimensional numerical simulations. For unburned gas injection in the outward and inward directions, the rotating direction of the detonation wave is set so that the azimuthal velocity enhances the radial electromotive force. The simulation results show that the power output in the outward flow configuration exceeds that of the inward flow configuration. In the outward flow configuration, the radial gas velocity around the contact surface is the main contributor to the power generation, while in the inward flow configuration, the low gas velocity in almost the entire region and the vortices around the contact surface lead to poor power output. The characteristics in not only the power output mode but also the power input mode in which the voltage is applied externally between the electrodes are investigated. Under the positive load voltage, high enough for providing negative current, the Lorentz force occurs in the same direction as the propagation of the detonation wave; otherwise, the Lorentz force is induced in the opposite direction of the detonation wave.