Shanghai Lingang New City, located in the southeast corner of Shanghai, was constructed by land reclamation from 2002 to 2005, in an area where the geological structure is prone to subsidence over time. Firstly, we explore the spatio-temporal pattern of ground subsidence and its mechanism using the Persistent Scatterers Interferometric Synthetic Aperture Radar (PSInSAR) technique by processing 50 scenes of Sentinel-1A images acquired from May 2016 to May 2018. In order to assess the accuracy of PSInSAR derived deformation, we collect the first-class leveling data at two benchmarks located in the study area; the comparison between the two settlement indicates that the maximum difference is 1.93 mm and 2.9 mm, respectively, which validates the PSInSAR’s high accuracy. We then obtain the skeleton release coefficients by the joint analysis of PSInSAR measurements and groundwater level data. Finally, we find that this coastal area has undergone both elastic and inelastic deformation from 2016 to 2018. The outcome shows that the combination of different techniques is conductive to understand the deformation mechanism of the aquifer system in these coastal areas, which is expected to be a valuable reference for ground subsidence monitoring and groundwater extraction management.
With the rapid development of interferometric synthetic aperture radar (InSAR) measurement technology, its measurement accuracy requirements are increasing. Atmospheric delay errors must be corrected, especially in the case of crustal deformation monitoring, the 20% variation of tropospheric water vapor among InSAR pairs generally produces range from 10 cm to 14 cm deformation errors. Such errors can be of the same magnitude as the annual changes in crustal deformation, or even greater, masking crustal deformation information and seriously affecting the results of crustal deformation monitoring. Therefore, in order to obtain a more accurate InSAR atmospheric delay correction model, this paper calculated and integrated atmospheric delays that were estimated by different sources, including the 37 pressure levels of the fifth generation of the European Centre for Medium-Range Weather Forecasts (ECMWF)) numerical weather prediction model, ECMWF Reanalysis v5 (ERA5), and Global Navigation Satellite System (GNSS) measurement data from the crustal movement observation network of China, based on the variance component estimation (VCE) weighting method. The results showed that the integrated model, based on the VCE method, is better than the generic atmospheric correction online service (GACOS) model for InSAR measuring of crustal deformation. The precision in monitoring crustal deformations was improved by approximately 5 mm, the correlation coefficient of atmospheric delay errors and crustal deformations improved from 0.287 to 0.347, and accuracy improved by approximately 25%. However, the improvement in accuracy was limited because of system error decoherence that was induced by atmospheric noise caused by abundant vegetation or snow cover. Therefore, in order to achieve more accurate results, we recommend the adoption of the multi-source integrated atmospheric delay correction model, based on the VCE method, for InSAR high-precision measuring of crustal deformation and seismic activities.
Three-dimensional deformation is an important input to explore seismic mechanisms and geodynamics. The GNSS and InSAR technologies are commonly used to obtain the co-seismic three-dimensional deformation field. This paper focused on the effect of calculation accuracy caused by the deformation correlation between the reference point and the points involved in the solution, to build a high-accuracy three-dimensional deformation field for a detailed geological explanation. Based on the variance component estimation (VCE) method, the InSAR LOS, azimuthal deformation, and the GNSS horizontal and vertical deformation were integrated to solve the three-dimensional displacement of the study area in combination with the elasticity theory. The accuracy of the three-dimensional co-seismic deformation field of the 2021 Maduo MS7.4 earthquake obtained by the method proposed in this paper, was compared with that obtained from the only InSAR measurements obtained using a multi-satellite and multi-technology approach. The results showed the difference in root-mean-square errors (RMSE) of the integration and GNSS displacement was 0.98 cm, 5.64 cm, and 1.37 cm in the east–west, north–south and vertical direction respectively, which was better than the RMSE of the method using only InSAR and GNSS displacement, which was 5.2 cm and 12.2 cm in the east–west, north–south, and no vertical direction. With the geological field survey and aftershocks relocation, the results showed good agreement with the strike and the position of the surface rupture. The maximum slip displacement was about 4 m, which was consistent with the result of the empirical statistical formula. It was firstly found that the pre-existing fault controlled the vertical deformation on the south side of the west end of the main surface rupture caused by the Maduo MS7.4 earthquake, which provided the direct evidence for the theoretical hypothesis that large earthquakes could not only produce surface rupture on seismogenic faults, but also trigger pre-existing faults or new faults to produce surface rupture or weak deformation in areas far from seismogenic faults. An adaptive method was proposed in GNSS and InSAR integration, which could take into account the correlation distance and the efficiency of homogeneous point selection. Meanwhile, deformation information of the decoherent region could be recovered without interpolation of the GNSS displacement. This series of findings formed an essential supplement to the field surface rupture survey and provided a novel idea for the combination of the various spatial measurement technologies to improve the seismic deformation monitoring.