Efforts to reduce the use of solid wood have led to an increase in the production of wood-based products especially particleboard. The wood industry is now exploring alternative materials such as crop residue, agricultural biomass, and non-woody plants to meet the demand for the wood-based products. This article focuses on the potential of Nipah palm frond, an abundant but underutilized non-wood resource in Sarawak, as a potential raw material for particleboard. Since the research on Nipah plant is still relatively new, no commercialised products have been developed from this plant. Therefore, this review paper evaluates the properties of Nipah palm frond and its compatibility with particleboard processing parameters in order to produce particleboard for non-construction applications. Despite limitations in raw material properties, prior studies suggest Nipah palm frond particles can be used to produce medium-density particleboard. The article offers comprehensive rationale for product development and provides recommendations for processing parameters, offering insights into the potential of this sustainable resource in the wood-based industry.
4 November 2018 in Jurnal Teknologi (Sciences & Engineering)
This study summarizes the research on organic fillers, where eggshells were used as the reinforcement and banana peels as the matrix in the manufacturing of biocomposite thin film. Banana peel fibers exhibit a good characteristic of renewable material for the substitution of cement-based composites. However, biocomposite properties are limited by the poor adhesion between natural fiber interface and polymer matrix, which can be improved by chemical modification of fibers. In this research, banana peels were subjected to silane treatment. Biocomposite thin film manufacturing processes were carried out using blending and hand lay-up techniques with various concentrations of epoxy/waste banana peels/eggshell filler (EWE) ratios (EWE 0%, EWE 5%, and EWE 10%). X-ray diffraction (XRD), Fourier transform infrared (FTIR), thermogravimetric analysis (TGA), and thickness swelling test were conducted on silane-treated and untreated banana peel biocomposite samples. In XRD analysis, it was found that EWE 10% sample had the highest crystallinity compared to EWE 0% and EWE 5%, and silane-treated samples had higher crystallinity than untreated samples. For FTIR test, lignin component was removed in silane treatment based on the changes of IR peak characteristic where the new bonds (-Si-O-C-, -Si-O-Si-, and -Si-C-) were found in treated samples. Besides, TGA results showed that the thermal stability of silane-treated samples was improved significantly with the increase of eggshell filler percentage, which was proven by the decrease in the decomposition stage. In thickness swelling test, the samples achieved higher swelling percentage as the percentage of eggshell filler increased. However, the decrease of 5–6% in thickness swelling of treated samples was possibly offset by the enhancement in fiber/matrix interfacial adhesion.
This study was carried to investigate changes in the oil heat treated 18-years old of planted Acacia mangium. Harvested trees segregated into bottom, middle and top portions containing heartwood and sapwood were oil heat treated in stainless tank with palm crude oil as heating medium at temperatures of 180oC, 200oC and 220oC for 30, 60 and 90 minutes respectively. The evaluation of the changes in the wood were performed by standards using a Minolta Chroma Meter, TAPPI Standard T204 om-88, TAPPI Standard T203 cm-99, TAPPI Standard T222 cm-02, and BS EN 310:1993 static bending tests. The relationship between the changes in the colour, mechanical and chemical composition, were made using correlation analysis. The result showed oil-heat treatment reduced the lightness of the wood and darkened the both parts of the wood. The strength of the wood reduced slightly after the oil-heat treatment. In the chemical compositions, the percentages of the holocellulose, α-cellulose, hemicellulose and extractive contents decrease with the increase in treatment duration and temperature. The oil heat treatment process at 200°C for duration 60 minutes is recommended for acacia mangium wood as it improved the colour of Acacia mangium and standardized the colour of sapwood and heartwood. The loss in strength at this temperature and duration is acceptable as the treated wood only loss up to 15% strength in MOR and 10.7% in MOE.
The study was carried out to determine the physical and mechanical properties of composite lumber made from cassava (Mahinot esculenta Crantz) and bamboo (Bambusa vulgaris) in different ratios which is 100% cassava with 0% bamboo, 75% cassava with 25% bamboo, 50% cassava with 50% bamboo, 25% cassava with 75% bamboo and 0% cassava with 100% bamboo. The tests samples for determining the strength properties were divided into two categories namely mechanical testing and physical testing. Basic density of the samples was carried out for physical testing. The lowest basic density was in samples with 100% cassava which is 0.49 g/cm3 and highest in samples with 100% bamboo which is 0.68 g/cm3 . Two tests for the mechanical testing are bending test and compression test. In bending test, modulus of elasticity (MOE) and modulus of rupture (MOR) were both highest for samples with 100% bamboo which the reading of MOE was 16794.03 N/mm2 and 122.52 N/mm2 for MOR. Similar to the bending test, compression test is the highest for the samples with 100% bamboo which are 65.58 N/mm2 . From statistical analysis, the basic density, static bending can compression strength give significant value at 95% confidence interval.