Timothy Dean

Timothy Dean

Auto-generated profile, based on publicly available information

Timothy Dean

Curtin University

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 November 2013 in Geophysical Prospecting
Verified
Journal Article
Closed access
PDF file
TDT. Dean
T. Dean

1 August 2016 in The Leading Edge
Verified
Journal Article
Closed access
TDTimothy Dean
Timothy Dean
JQJohn Quigley
John Quigley
SMScott MacDonald
Scott MacDonald
CRColin Readman
Colin Readman
There is currently much work being done to improve the low-frequency content of land vibroseis data. Although techniques exist for designing sweeps that can extend the bandwidth down to as low as 1 Hz, the inclusion of these frequencies comes at considerable cost, either in the time taken to acquire a sweep or in the reduction of the total sweep energy. We describe the limitations on vibrator performance and how those limitations can be overcome using specialized sweep-design techniques. Perhaps more importantly, we describe how such sweeps can be optimized in terms of maximizing their energy content and verifying their performance.

1 September 2020 in The Leading Edge
Verified
Journal Article
Closed access
TDTimothy Dean
Timothy Dean
MHMus'AB Al Hasani
Mus'AB Al Hasani
The results of an experiment aimed at identifying the nature of major noise sources within an urban area are described. We found the strongest noise source to be an irrigation pump located adjacent to the geophones. The noise from the pump had a narrow bandwidth centered at 75 Hz with a duration of 5 minutes every 17 and 34 minutes during the day and night, respectively. Traffic noise was mainly restricted to between 10 and 25 Hz, with its strength decreasing between 9 p.m. and 6 a.m. Passing aircraft resulted in noise between 30 and 200 Hz lasting about 1 minute. Electrical noise was observed at the supply frequency of 50 Hz, although additional noise at 45 Hz also was observed. Given these results we recommended that acquisition within the area should be restricted to late evening or early morning, receiver locations should be selected to avoid strong localized sources of electrical and/or mechanical noise, and any cables associated with the recording system should be as short as possible (although nodal systems are preferable). If nodal systems are deployed for logistical reasons, real-time noise monitoring should be deployed to identify and avoid bursts of high-amplitude, short-duration noise.

18 March 2015 in Geophysics
Verified
Journal Article
Closed access
TDTimothy Dean
Timothy Dean
JDJ. Christian Dupuis
J. Christian Dupuis
RHRakib Hassan
Rakib Hassan
GLGuofa Li
Guofa Li
HZHao Zheng
Hao Zheng
WHWei Huang
Wei Huang
The use of analog sensor arrays is often assumed to provide signal-to-ambient-noise improvements proportional to the square root of the number of sensors being summed. We determined via numerical modeling and field experiments that the improvements sought were significantly hindered once the ambient noise exhibited coherence over the array being summed. As a first step, a numerical model was developed to explore the optimal sensor spacing based on the average correlation coefficient between sensors. Field experiments were then carried out to measure ambient noise using closely spaced geophones at several sites in Perth, Western Australia. We show that the measured noise at six test sites was strongly coherent over distances of up to 10 m, with the level of coherency being inversely proportional to frequency. The resulting optimum geophone spacing under our field conditions was determined to be 7.5 m. These results offered further encouragement to reassess our use of analog arrays and to consider recording the output from individual sensors. In addition to the benefits from postacquisition noise suppression, this approach will enable increased trace density without degradation of the signal caused by strong coherent noise sources over acquisition spreads.

1 December 2013 in ASEG Extended Abstracts
Verified
Journal Article
Open access
PDF file
TDTimothy Dean
Timothy Dean
DLDarvin Lane
Darvin Lane
JTJohn Tulett
John Tulett
MPMark Puckett
Mark Puckett
Vibrators are the preferred sources for onshore vertical seismic profile (VSP) surveys. Truck-mounted units are especially useful as they are more road mobile than buggy-based units. In particular, they can be driven directly to the wellsite, resulting in improved response times, simplified logistics with fewer vehicles and personnel at the wellsite and improved transport safety. Acquiring broad-bandwidth, high-quality VSP data, using state-of-the art vibrator equipment, however, has generally required the use of the latest buggy-mounted vibrators, compromising well-site logistics and transportation safety for VSP operations. To deliver optimum performance, two new truck vibrator models specifically designed to take advantage of all of the most recent developments in vibrator technology while retaining the logistical advantages of truck-mounted units have been developed. These new truck-mounted vibrators offer greatly improved data quality with tests showing that they can transmit a signal with a frequency bandwidth of 6.6 octaves compared to previous models which can only transmit 2.5 octaves. Being mounted on modern truck chassis these vehicles retain all the mobility and HSE advantages of truck vibrators.

1 December 2015 in ASEG Extended Abstracts
Verified
Journal Article
Open access
PDF file
PCPieter Claassen
Pieter Claassen
TDTimothy Dean
Timothy Dean
BMBen McCarthy
Ben McCarthy
The moving coil geophone is still the most commonly used sensor for land seismic surveys despite the introduction of other sensors. Modern geophone development has reached the stage where the signal recorded is of very high quality, but it can still be affected by the geophone being placed on an angle relative to the vertical ('tilt'). This paper describes the acquisition and analysis of field measurements using tilted geophones. It is shown that the critical angle of the 10 Hz geophones used for this test is 55°. For data recorded using vertically placed geophones separated by only 10 cm the perturbation level (the difference between the data recorded by adjacent geophones) averaged 8% and increased to more than 50% at tilt angles of 40º. The level of perturbation is heavily dependent on the orientation of the tilt angle relative to the source-detector axis, for example, for a geophone tilted at an angle of 30°, the perturbation varied between 14% and 48%. The obvious solution to these issues is to record data using sensors that have been planted extremely carefully or to use other sensors, such as digital accelerometers or 3C sensors that have the effect of tilt removed during processing.