18 November 2013 in Green Chemistry
Epoxy–clay nanocomposites derived from renewable soybean oils and organo modified montmorillonite clay were prepared. Improved efficiency and performance were achieved through application of new, low viscosity, glycidyl esters of epoxidized fatty acids (EGS) as the epoxy monomer and 4-methyl-1,2-cyclohexanedicarboxylic anhydride as the comonomer. Tensile testing showed that 1 wt% of clay improved nanocomposite strength and modulus by 22% and 13%, respectively, compared to neat polymer. Tensile modulus could be increased up to 34% by nanocomposite clay without any sacrifice of strength. Three types of dispersion techniques, mechanical stirring, high speed shearing, and ultrasonication, were carried out to disperse the clay directly into the epoxy or anhydride portion of the thermoset system without the need of additional solvent. Dispersion of the clay particles into monomer was assessed by means of solubility parameters and optical and scanning electron microscopies, and quality of dispersion further confirmed by small angle X-ray scattering and transmission electron microscopy. Sonication dispersion of clay into the epoxy portion was needed to optimize the dispersion and exfoliation of clay and the higher mechanical and thermal strength of the nanocomposites. The nanocomposites’ morphologies were a mix of intercalated and exfoliated structures, dependent on the dispersion technique. The optimum tensile strength and glass transition temperatures of the nanocomposites were a function of clay concentration and dispersion morphology.
21 February 2012 in Journal of Reinforced Plastics and Composites
In spite of numerous advantages of open-cell core sandwich composites, the applications have been limited due to the problems involved in manufacturing using low cost processes. Resin accumulation in the core is a major challenge in the fabrication of honeycomb sandwich panels using resin infusion techniques. Foam-filled cores and polymer film barriers are some of the methods used in the literature to address this issue. However, these techniques will increase the weight of the sandwich composites. In this study, honeycomb sandwich panels were manufactured using commercially available film adhesive and modified vacuum-assisted resin transfer molding process. The resin incursion into the core openings was investigated. No accumulation of resin was observed in the core. Flatwise tension, flatwise/edgewise compression, and three-point bending tests were conducted to evaluate the mechanical performance of the sandwich composites. The performance of sandwich panels during a low-velocity impact event was also evaluated. Results indicate that the vacuum-assisted resin transfer molding process can be successfully used to manufacture honeycomb composite sandwich structures using currently available barrier adhesive films.
5 February 2013 in Polymer International
1 November 2014 in Polymers and Polymer Composites
A novel optically-transparent glass fibre reinforced polymer matrix composite has been developed by infusing a clear epoxy resin system of matching refractive index into a conventional E-glass fabric preform. Transparent composites are manufactured using a low cost, environmentally friendly vacuum infusion process. Physical and mechanical tests have been conducted. Transparent composites manufactured using the modified vacuum infusion process had a fibre volume fraction of 40%. Tensile strength and tensile modulus of these composites were 374.9 MPa and 31.74 GPa respectively. The results indicate that the transparent composites possess good physical and mechanical properties. These transparent composites form a good base for developing new generation transparent armour systems.
22 April 2014 in Advanced Composite Materials
Glass fiber-reinforced polymer composites have promising applications in infrastructure, marine, and automotive industries due to their low cost, high specific stiffness/strength, durability, and corrosion resistance. Polyurethane (PU) resin system is widely used as matrix material in glass fiber-reinforced composites due to their superior mechanical behavior and higher impact strength. Glass fiber-reinforced PU composites are often manufactured using pultrusion process, due to shorter pot life of PU resin system. In this study, E-glass/PU composites are manufactured using a low-cost vacuum-assisted resin transfer molding process. A novel, one-part PU thermoset resin system with a longer pot life is adopted in this study. Tensile, flexure, and impact tests are conducted on both the thermoset PU neat resin system and E-glass/PU composites. A three-dimensional finite element model is developed in a commercial finite element code to simulate the impact behavior of E-glass/PU composite for three different energy levels. Finite element model is validated by comparing it with experimental results.
31 October 2013 in Polymer Composites