25 October 2017 in RSC Advances
The adsorption of scandium from diluted, acidic solutions by a supported ionic liquid phase (SILP) was investigated, as part of a process for recovery of scandium from bauxite residue (red mud). Both dry impregnation and covalent linking were studied for the SILP preparation. The SILP betainium sulfonyl(trifluoromethanesulfonylimide) poly(styrene-co-divinylbenzene) [Hbet–STFSI–PS–DVB] was prepared by covalent linking of the ionic liquid to the resin and this resulted in an adsorbent suitable for scandium recovery. For a chloride feed solution, the effects of pH, contact time, adsorption capacity, desorption, reusability of adsorbent and the influence of Fe(III), Al(III) and Ca(II) on the Sc(III) adsorption were studied. The adsorption of Sc(III) from nitrate and sulfate feed solution under optimal conditions was studied as well. The adsorption kinetics followed a pseudo-second order kinetic model. Equilibrium studies at room temperature showed that the experimental data could be well fitted by the Langmuir isotherm model. The stripping of Sc(III) from the loaded SILP was achieved with 1 M sulfuric acid. The SILP was stable and could be reused for seven adsorption/desorption cycles without significant losses in its adsorption efficiency for Sc(III).
26 March 2018 in RSC Advances
Bauxite residue (BR) contains substantial concentrations of rare-earth elements (REEs), but their recovery is a challenge. Acidic BR leachates typically comprise much higher concentrations of base elements (g L−1) than those of the REEs (ppm). Thus, adsorbents that are highly selective for the REEs over the base elements are required for the separation. The novel supported ionic liquid phase (SILP) betainium sulfonyl(trifluoromethanesulfonylimide) poly(styrene-co-divinylbenzene) [Hbet-STFSI-PS-DVB] was evaluated for the uptake of REEs (Sc, Y, Nd, Dy) in the presence of base elements (Ca, Al, Fe) from BR leachates. Breakthrough curves from acidic nitrate and sulfate media were investigated, as both HNO3 and H2SO4 are commonly used for leaching of BR. The SILP exhibited a superior affinity for REEs in both media, except in the case of Sc(III) from the sulfate feed. The recovery rates of the trace amounts of REEs from the real nitrate feed were remarkably high (71.7–100%) via a simple chromatography separation, without requiring complexing agents or a pretreatment for the removal of interfering elements. The REEs were purified from the base elements and separated into three sub-groups (scandium, light REEs and heavy REEs) by an optimized elution profile with H3PO4 and HNO3 in a single chromatographic separation step.
1 September 2018 in Hydrometallurgy
31 October 2017 in Journal of Materials Chemistry A
The separation of rare-earth elements (REEs) is usually carried out by a multi-stage solvent extraction process utilising organophosphorus extractants. Inspired by the structure of the solvating extractant tri-n-butyl phosphate (TBP), new sorbents were designed by covalently attaching short n-alkyl chains (ethyl, n-propyl and n-butyl) to titanium(IV) phosphate functionalised mesoporous MCM-41 silica by a layer-by-layer grafting route. Mesoporous MCM-41 silica served as a versatile porous support and the grafted titanium(IV) derivatives provided enhanced acid stability and solvating extraction capability. Various characterisation methods including solid-state 13C, 29Si and 31P magic-angle spinning (MAS) nuclear magnetic resonance (NMR) and simultaneous thermogravimetry and differential scanning calorimetry-mass spectroscopy (TG/DSC-MS) were used to confirm the ligand attachment. The hybrid materials showed a better uptake of rare-earth ions from nitrate feed solution than the unmodified inorganic material. The optimal separation factor (SF) obtained for scandium–lanthanum separation is in excess of 100 000 at pH 2.1. The SFs calculated for dysprosium–neodymium are approximately 3, which is comparable to that of TBP in a typical solvent extraction setup. This study provides a new strategy to design inorganic–organic hybrid sorbents based on the structure of organophosphorus extractants via metal(IV)–O–P bonds.
28 July 2020 in Industrial & Engineering Chemistry Research
Solvometallurgy is a new branch of extractive metallurgy in which green organic solvents are used instead of aqueous solutions to improve selectivity in separation processes. In the present study, non-aqueous leaching of a Greek bauxite residue (BR) was performed and scandium was separated from other elements in the leachate by column chromatography. At first, the selectivity of sorbents for scandium(III) over iron(III) was tested in batch mode using various organic solvents. Three sorbents were tested: 1) a carboxylic acid-functionalized supported ionic liquid phase (SILP), 2) silica (SiO2), and 3) silica functionalized with ethylenediaminetetraacetic acid (SiO2‒TMS‒EDTA). The best separation of scandium and iron was achieved from ethanolic solution by the SILP. The BR was then leached with 0.7 mol L‒1 HCl in ethanol or in water. The leaching efficiency of scandium with both lixiviants was similar. However, much less sodium was leached and silica remained in solution when leaching was performed with the ethanolic lixiviant. By using ethanol as opposed to water, the serious drawback of silica gel formation that is taking place in the aqueous leachate of BR was circumvented. The sorption preference of the SILP for metal ions in the ethanolic leachate was partly reversed compared to the aqueous leachate. Iron was separated from other metals of the ethanolic BR leachate by a simple elution with ethanol. The formation of the anionic tetrachloroferrate(III) complex, [FeCl4]‒, enabled the selective elution. This complex was not observed in the aqueous leachate of BR. Scandium was separated from the vast majority of other components of the BR by elution with 0.1 mol L‒1 H3PO4.
23 May 2022 in Journal of Sustainable Metallurgy
The use of lithium in manufacturing of lithium-ion batteries for hybrid and electric vehicles, along with stringent environmental regulations, have strongly increased the need for its sustainable production and recycling. The required purity of lithium compounds used for the production of battery components is very high (> 99.5%). In this work, a solvometallurgical process that exploits the differences in solubility between LiCl and other alkali and alkaline-earth chlorides and hydroxides in ethanolic solutions has been investigated for the purification of LiCl to battery grade at room temperature. A closed-loop flowsheet based on the green solvent ethanol is proposed for purification of LiCl, a precursor for battery-grade LiOH·H2O. High-purity LiCl solution (> 99.5% Li) could be obtained in a single-process step comprising the simultaneous selective dissolution of LiCl and the precipitation of Mg(OH)2 and Ca(OH)2 using LiOH·H2O in 95 vol% ethanol. However, the analogous process in aqueous solution resulted in impure LiCl (typically less than about 75%). Graphical Abstract