7 October 2020 in Plant Direct
Changes in canopy architecture traits have been shown to contribute to yield increases. Optimizing both light interception and light interception efficiency of agricultural crop canopies will be essential to meeting the growing food needs. Canopy architecture is inherently three‐dimensional (3D), but many approaches to measuring canopy architecture component traits treat the canopy as a two‐dimensional (2D) structure to make large scale measurement, selective breeding, and gene identification logistically feasible. We develop a high throughput voxel carving strategy to reconstruct 3D representations of sorghum from a small number of RGB photos. Our approach builds on the voxel carving algorithm to allow for fully automatic reconstruction of hundreds of plants. It was employed to generate 3D reconstructions of individual plants within a sorghum association population at the late vegetative stage of development. Light interception parameters estimated from these reconstructions enabled the identification of known and previously unreported loci controlling light interception efficiency in sorghum. The approach is generalizable and scalable, and it enables 3D reconstructions from existing plant high throughput phenotyping datasets. We also propose a set of best practices to increase 3D reconstructions’ accuracy.
24 May 2022 in Computer Graphics Forum
18 May 2020 in IEEE Transactions on Visualization and Computer Graphics
Procedural modeling has produced amazing results, yet fundamental issues such as controllability and limited user guidance persist. We introduce a novel procedural model called PICO (Procedural Iterative Constrained Optimizer) and PICO-Graph that is the underlying procedural model designed with optimization in mind. The key novelty of PICO is that it enables the exploration of generative designs by combining both user and environmental constraints into a single framework by using optimization without the need to write procedural rules. The PICO-Graph procedural model consists of a set of geometry generating operations and a set of axioms connected in a directed cyclic graph. The forward generation is initiated by a set of axioms that use the connections to send coordinate systems and geometric objects through the PICO-Graph, which in turn generates more objects. This allows for fast generation of complex and varied geometries. Moreover, we combine PICO-Graph with efficient optimization that allows for quick exploration of the generated models and the generation of variants. The user defines the rules, the axioms, and the set of constraints; for example, whether an existing object should be supported by the generated model, whether symmetries exist, whether the object should spin, etc. PICO then generates a class of geometric models and optimizes them so that they fulfill the constraints. The generation and the optimization in our implementation provides interactive user control during model execution providing continuous feedback. For example, the user can sketch the constraints and guide the geometry to meet these specified goals. We show PICO on a variety of examples such as the generation of procedural chairs with multiple supports, generation of support structures for 3D printing, generation of spinning objects, or generation of procedural terrains matching a given input. Our framework could be used as a component in a larger design workflow; its strongest application is in the early rapid ideation and prototyping phases.
8 March 2025 in Plant Phenomics
Differences in canopy architecture play a role in determining both the light and water use efficiency. Canopy architecture is determined by several component traits, including leaf length, width, number, angle, and phyllotaxy. Phyllotaxy may be among the most difficult of the leaf canopy traits to measure accurately across large numbers of individual plants. As a result, in simulations of the leaf canopies of grain crops such as maize and sorghum, this trait is frequently approximated as alternating 180° angles between sequential leaves. We explore the feasibility of extracting direct measurements of the phyllotaxy of sequential leaves from 3D reconstructions of individual sorghum plants generated from 2D calibrated images and test the assumption of consistently alternating phyllotaxy across a diverse set of sorghum genotypes. Using a voxel-carving-based approach, we generate 3D reconstructions from multiple calibrated 2D images of 366 sorghum plants representing 236 sorghum genotypes from the sorghum association panel. The correlation between automated and manual measurements of phyllotaxy is only modestly lower than the correlation between manual measurements of phyllotaxy generated by two different individuals. Automated phyllotaxy measurements exhibited a repeatability of R2 = 0.41 across imaging timepoints separated by a period of two days. A resampling based genome wide association study (GWAS) identified several putative genetic associations with lower-canopy phyllotaxy in sorghum. This study demonstrates the potential of 3D reconstruction to enable both quantitative genetic investigation and breeding for phyllotaxy in sorghum and other grain crops with similar plant architectures.
19 November 2024 in ACM Transactions on Graphics
Procedural implicit surfaces are a popular representation for shape modeling. They provide a simple framework for complex geometric operations such as Booleans, blending and deformations. However, their editability remains a challenging task: as the definition of the shape is purely implicit, direct manipulation of the shape cannot be performed. Thus, parameters of the model are often exposed through abstract sliders, which have to be nontrivially created by the user and understood by others for each individual model to modify. Further, each of these sliders needs to be set one by one to achieve the desired appearance. To circumvent this laborious process while preserving editability, we propose to directly manipulate the implicit surface in the viewport. We let the user naturally interact with the output shape, leveraging points on a co-parameterization we design specifically for implicit surfaces, to guide the parameter updates and reach the desired appearance faster. We leverage our automatic differentiation of the procedural implicit surface to propagate interactions made by the user in the viewport to the shape parameters themselves. We further design a solver that uses such information to guide an intuitive and smooth user workflow. We demonstrate different editing processes across multiple implicit shapes and parameters that would be tedious by tuning sliders.