17 July 2018 in IEEE Transactions on Power Electronics
This paper presents a new Insulated Gate Bipolar Transistor (IGBT) over-current detection method based on the analysis of the gate voltage. IGBT gate voltage turn-on transient pattern is analyzed for the detection of IGBT Hard Switching Fault (HSF). On-state gate voltage is monitored to detect IGBT Fault Under Load (FUL). IGBT turn-off Miller plateau voltage is extracted and measured to sense the IGBT collector current in case of over-load condition. Compared to the commonly used IGBT short circuit detection methods or collector current sensing methods, this method can provide indirect fast detection of IGBT short circuit and accurate measurement of over-load within one switching period. The feasibility and effectiveness of the proposed approach are validated both by simulation and experimental results. Measurement results show that HSF and FUL can be detected within 0.6 μs and 0.5 μs, respectively. By comparing the extracted plateau voltage (VPL) with a preset reference voltage (VOCx), the IGBT over-load can be detected with a maximum deviation of ±1.2 A when IC ranges from 3 to 110 A.
21 April 2015 in RSC Advances
Aluminum nitride (AlN) films have been deposited on AlGaN/GaN heterostructure substrates by plasma enhanced atomic layer deposition (PEALD). Different annealing treatments were adopted to change film structure and improve performance. Chemical composition, crystallinity, and electrical properties were studied for AlN films. The results show that some crystal grains appear in the films after annealing at a temperature of over 800 °C. The film crystalline quality increases as the annealing temperature rises. The N–O–Al bond decomposes during the high temperature annealing in N2, and some new N–Al bonds are formed in the AlN films. Annealing promotes the elemental interdiffusion between the films and the substrates. High-temperature annealing at 1000 °C in a nitrogen atmosphere can effectively promote complete nitridation of the AlN film, reduce the nitrogen vacancies, and cause the AlN film to form a semiconductor-like structure.
16 February 2017 in RSC Advances
In this paper, AlNO nano-films have been deposited on an AlGaN/GaN heterojunction by alternating growth of AlN and Al 2 O 3 using plasma enhanced atomic layer deposition (PEALD).
11 December 2014 in Physical Chemistry Chemical Physics
Al2O3-doped HfO2 with both amorphous state and high relative permittivity was directly deposited on graphene by atomic layer deposition.
28 June 2018 in IEEE Transactions on Electron Devices
In order to analyze the influence of different substrates on the performance of metal-insulator-semiconductor AlGaN/GaN high-electron mobility transistors, devices on free-standing GaN (FS-GaN), silicon, and sapphire substrates with similar AlGaN/GaN top layers were fabricated. Compared with Si and sapphire substrates, the devices on the FS-GaN substrate not only achieve remarkable improvement in the direct current characteristics but also have much better thermal stability and can significantly suppress the self-heating effects, where the current density only decreases by 4% with the channel at 48 °C and an ambient of 25 °C. Owing to the lower trap and dislocation densities in the epitaxial layers, the dynamic performance and reliability of the devices on the FS-GaN substrate are also dramatically improved. With an off-state drain bias of 50 V kept for 10 s, the devices on the FS-GaN substrate only suffer a 10% increase in dynamic on resistance, much lower than the devices on the Si and sapphire substrates. In addition, all the devices were exposed to a 3-MeV proton irradiation with a dose of 3 x 10¹⁴ cm⁻². Compared with the devices before radiation treatment, the dynamic on resistance increases by 79% with a 20-V off-state stress for the devices on the FS-GaN substrate, while the increase is over 800% for the other devices. The lower performance degradation for the devices on the FS-GaN substrate indicates a lower displacement damage and better irradiation tolerance.
27 April 2015 in RSC Advances
Graphene can avoid the oxidation of Sb2Te3, eliminate the generation of an interface layer and maintain the crystal structures of Sb2Te3.