This study investigates the CdTe thin films prepared using two distinct methods: classical and cryogenic techniques of thermal evaporation within a substrate temperature range of 100–573 K. X-ray diffraction (XRD) analysis revealed cubic (111) crystal growth across all substrate temperatures, transitioning to an amorphous structure as the temperature approached 100 K. The CdTe thin film produced at 200 K stood out with superior structural properties, characterized by the lowest surface roughness (Ra = 1.1 nm) and a highly uniform grain structure, attributed to the soliton growth mechanism. The grain sizes of the thin films decreased from 53.6 to 14.8 nm with a decreasing substrate temperature, correlating with an increase in resistivity (1.88–3.87 × 103 Ω·cm) and band gap energy (1.48–1.65 eV). The CdTe thin films produced at the substrate temperatures of 200 and 473 K were relatively more stoichiometric. Photoluminescence (PL) measurements highlighted the enhanced luminescence intensity near the band-edge at 200 K, further confirming the optimal stoichiometry and structural quality of CdTe films produced in this regime. The findings highlight that the cryogenic technique could provide a significant advantage for applications such as quantum dots or nano-optoelectronics, where nanoparticle size and distribution must be precisely controlled.
12 June 2017 in International Journal of Green Energy
This paper presents the performance of the solid-oxide fuel cell/gas turbine hybrid power generation system with heat recovery waste unit based on the energy and exergy analyses. The effect of air inlet temperature and air/fuel ratio on exergy destruction and network output is determined. For the numerical calculations, air inlet temperature and air fuel ratio are increased from 273 to 373 K and from 40 to 60, respectively. The results of the numerical calculations bring out that total exergy destruction quantity increases with the increase of air inlet temperature and air/fuel ratio. Furthermore, the maximum system overall first and second law efficiencies are obtained in the cases of air inlet temperature and air/fuel ratio equal to 273 K and 60, respectively, and these values are 62.09% and 54.91%.
28 December 2023 in Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji
Güneş enerjisinden gerek termal gerekse elektrik uygulamalarında elde edilen faydalı enerji yüzeye gelen ışınıma bağlıdır ve bu ışınım miktarı konum, zaman, iklimsel koşullar ve çevre koşullarına göre değişmektedir. Güneş enerji destekli enerji sistemlerinin etkin bir şekilde tasarlanması ve çalıştırılması için ışınım miktarının doğru bir şekilde belirlenmesi önem arz etmektedir. Bu çalışmada Türkiye’nin farklı iklim kuşaklarında yer alan dört il (Kayseri, Rize, Hakkari ve İzmir) için MATLAB uygulamasıyla Yapay Sinir Ağları (YSA) modeli oluşturulup güneş ışınımı tahmini yapılmıştır. Güneş ışınımı tahmini yapılırken illerin enlem, boylam ve rakımdan oluşan coğrafik verilerinin etkisinin yanı sıra ortalama sıcaklık, bağıl nem, bulutluluk ve buhar basıncı gibi meteorolojik verilerin etkisi de ele alınmıştır. Tüm bu etkenler göz önüne alındığında kurulan modelde en iyi tahminleme sonucu R2=0.93 değeriyle Hakkari ilinde olup sırasıyla İzmir, Kayseri ve Rize illeri takip etmektedir. Her bir il için YSA ile tahmin edilen değerler ile ölçülen değerler arasında uyum olduğu görülmüştür.