Bumman Kim

Bumman Kim

Auto-generated profile, based on publicly available information

Bumman Kim

Department of Electrical Engineering, Pohang University of Science and Technology, Pohang, South Korea

Research Focus & Metrics

Academic Career Length

26Years (2001-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 November 2016 in IEEE Transactions on Microwave Theory and Techniques
Verified
Journal Article
Closed access
BPByungjoon Park
Byungjoon Park
SJSangsu Jin
Sangsu Jin
DJDaechul Jeong
Daechul Jeong
JKJooseung Kim
Jooseung Kim
YCYunsung Cho
Yunsung Cho
BKBumman Kim
Bumman Kim
A Ka-band highly linear power amplifier (PA) is implemented in 28-nm bulk CMOS technology. Using a deep class-AB PA topology with appropriate harmonic control circuit, highly linear and efficient PAs are designed at millimeter-wave band. This PA architecture provides a linear PA operation close to the saturated power. Also elaborated harmonic tuning and neutralization techniques are used to further improve the transistor gain and stability. A two-stack PA is designed for higher gain and output power than a common source (CS) PA. Additionally, average power tracking (APT) is applied to further reduce the power consumption at a low power operation and, hence, extend battery life. Both the PAs are tested with two different signals at 28.5 GHz; they are fully loaded long-term evolution (LTE) signal with 16-quadrature amplitude modulation (QAM), a 7.5-dB peak-to-average power ratio (PAPR), and a 20-MHz bandwidth (BW), and a wireless LAN (WLAN) signal with 64-QAM, a 10.8-dB PAPR, and an 80-MHz BW. The CS/two-stack PAs achieve power-added efficiency (PAE) of 27%/25%, error vector magnitude (EVM) of 5.17%/3.19%, and adjacent channel leakage ratio (ACLR $_{\mathrm{ E-UTRA}}$ ) of −33/−33 dBc, respectively, with an average output power of 11/14.6 dBm for the LTE signal. For the WLAN signal, the CS/2-stack PAs achieve the PAE of 16.5%/17.3%, and an EVM of 4.27%/4.21%, respectively, at an average output power of 6.8/11 dBm.

22 January 2014 in IEEE Transactions on Microwave Theory and Techniques
Verified
Journal Article
Closed access
YCYunsung Cho
Yunsung Cho
DKDaehyun Kang
Daehyun Kang
JKJooseung Kim
Jooseung Kim
KMKyunghoon Moon
Kyunghoon Moon
BPByungjoon Park
Byungjoon Park
BKBumman Kim
Bumman Kim
This paper presents a linear Doherty power amplifier (PA) with enhanced back-off efficiency mode for handset applications. For linear Doherty operation, we analyze the gain modulation as well as the cancellation of the third-order intermodulation distortion in order to improve the linearity. A compact design method is also discussed to implement on a single chip for a handset. The proposed Doherty PA delivers good performance with regard to the third-generation (3G)/fourth-generation (4G) modulation signals. A switched-load power-mode PA is adopted in the proposed Doherty PA to enhance the efficiency in the low-power region with over 10-dB back-off. For demonstration purposes, the PA is implemented using an InGaP/GaAs heterojunction bipolar transistor and AlGaAs/InGaAs pseudomorphic high electron-mobility transistor process. The PA is tested at 1.85 GHz using both a long-term evolution signal with 16-quadrature amplitude modulation, 7.5-dB peak-to-average power ratio, and 10-MHz bandwidth (BW) and a wideband code division multiple access signal with 3.3-dB PAPR and 3.84-MHz BW. The proposed linear Doherty PA with an enhanced back-off efficiency mode delivers good performance in both the high- and low-power modes, implying that the dual-power-mode Doherty PA configuration can be a promising candidate for extending the battery life of handheld devices in 3G and 4G wireless communication systems.

9 September 2016 in IEEE Transactions on Microwave Theory and Techniques
Verified
Journal Article
Closed access
YCYunsung Cho
Yunsung Cho
KMKyunghoon Moon
Kyunghoon Moon
BPByungjoon Park
Byungjoon Park
JKJooseung Kim
Jooseung Kim
BKBumman Kim
Bumman Kim
This paper presents a voltage-combined CMOS Doherty power amplifier (PA) based on a transformer. The dynamic load modulation of the two-way transformer is analyzed in detail. A comparison between the current- and voltage-combined Doherty PAs shows that the Doherty PA based on a voltage-combining method delivers a broad bandwidth (BW) with a larger load tolerance. The proposed Doherty PA achieves close to ideal load modulation without additional offset line by manipulation of the output capacitances. For demonstration purposes, the PA and output combining transformer are implemented using a 0.18-μm CMOS process and an FR4 printed circuit board, respectively. The PA is tested at 880 MHz using a fully loaded long-term evolution signal with 16-quadrature amplitude modulation, 7.5-dB peak-to-average power ratio, and 10-MHz BW. The PA delivers a gain of 13.3 dB, a power-added efficiency of 47.4%, an error vector magnitude of 3.85%, and E-UTRAACLR of -33 dBc at an average output power of 27 dBm. This simple voltage-combined Doherty PA without any additional circuitry achieves good performance. These results show that the proposed CMOS Doherty PA is suitable for handheld PA applications.

12 August 2016 in IEEE Transactions on Microwave Theory and Techniques
Verified
Journal Article
Closed access
SKSeokhyeon Kim
Seokhyeon Kim
JMJunghwan Moon
Junghwan Moon
JLJuyeon Lee
Juyeon Lee
YPYunsik Park
Yunsik Park
DMDonggyu Minn
Donggyu Minn
BKBumman Kim
Bumman Kim
Accurate offset line design of Doherty amplifier is investigated to compensate the phase variation of the carrier and peaking amplifiers. The offset line at the peaking amplifier not only blocks the power leakage to the peaking amplifier at the OFF-state, but also assists in the load modulation like the offset line at the carrier amplifier. However, with the conventional offset line, the load is not properly modulated due to the phase variation of the class C peaking amplifier. Since the offset lines at the carrier and peaking power amplifiers (PAs) properly eliminate the reactive parts during the Doherty load modulation, the offset lines can handle the phase variation also. To compensate the phase variation, additional lines are added at the carrier and peaking amplifiers for the proper load modulation. With the new offset line, the load of the peaking amplifier can be properly modulated and the efficiency at the high power region is increased. In addition, the efficiency at the low power region is also increased due to the larger load of the carrier amplifier at the power region. The enhanced performance is validated by the Doherty PA employing CGH40045 devices at 1.94 GHz, applying drain bias voltage of 50 V. For the long term evolution signal with a 6.5 dB peak-to-average power ratio, the Doherty amplifier with the new offset line delivers a drain/power-added efficiency of 57%/54.8% which is 3.5%/3.1% higher than that with the conventional offset line at an output power of 45.4 dBm with the linearity -48.3 dBc using digital predistortion linearization.

19 January 2010 in IEEE Microwave and Wireless Components Letters
Verified
Journal Article
Closed access
JKJangheon Kim
Jangheon Kim
JSJunghwan Son
Junghwan Son
JMJunghwan Moon
Junghwan Moon
BKBumman Kim
Bumman Kim
A saturated Doherty power amplifier (PA) based on the saturated PA tuned by the self-generated harmonic currents is presented. When driven with mobile WiMAX 1FA signal, this Doherty PA demonstrates high efficiency performance (average 57%) over the WiMAX band from 2.5 GHz to 2.7 GHz. Simulated and experimental results allow the evaluation for the load modulation behavior of the saturated PA and bandwidth correlation between the Doherty and saturated unit PAs. The linearity requirement of the WiMAX signal is met using the digital feedback predistortion linearization technique.

1 January 2006
Verified
Conference Paper
Closed access
BKBumman Kim
Bumman Kim
JKJangheon Kim
Jangheon Kim
IKIldu Kim
Ildu Kim
JCJeonghyeon Cha
Jeonghyeon Cha
SHSungchul Hong
Sungchul Hong
This paper explains the basic circuit configuration of microwave Doherty amplifier and additional design methods for wide bandwidth and high power applications. This paper also presents the recent experimental results of the group using the uneven power drive. Most of the previous works about microwave Doherty amplifier have employed identical input drives. In this works, two 1:1(2-way) and a 1:2(3-way) Doherty amplifiers are implemented at 2.14GHz center frequency using LDMOS with a peak envelope power of 180 watt and 285 watt, respectively. The 2-way Doherty amplifiers are optimized at 25 watt average output power for high efficiency and linearity and the 3-way Doherty amplifier at 16 watt average output power for high linearity. The amplifiers are tested using WCDMA 4FA signal. The performances of the 2-way Doherty amplifier are compared with that of the comparable class AB amplifier and the Doherty amplifier with even power drive. The performances of the 3-way Doherty amplifier are compared with that of the comparable class AB amplifier. The experimental results show the superior performances of our Doherty amplifiers