Mauricio Morais de Lima

Mauricio Morais de Lima

Auto-generated profile, based on publicly available information

Mauricio Morais de Lima

Paul-Drude-Institut für Festkörperelektronik , Hausvogteiplatz 5-7, 10117 Berlin, Germany

Research Focus & Metrics

Academic Career Length

32Years (1995-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 June 2005 in Reports on Progress in Physics
Verified
Journal Article
Closed access
MLMaurício M de Lima
Maurício M de Lima
PSPaulo V Santos
Paulo V Santos

1 November 1999 in Journal of Applied Physics
Verified
Journal Article
Closed access
MLM. M. de Lima
M. M. de Lima
RLR. G. Lacerda
R. G. Lacerda
JVJ. Vilcarromero
J. Vilcarromero
FMF. C. Marques
F. C. Marques
The coefficient of thermal expansion (CTE), biaxial modulus, and stress of some amorphous semiconductors (a-Si:H, a-C:H, a-Ge:H, and a-GeCx:H) and metallic (Ag and Al) thin films were studied. The thermal expansion and the biaxial modulus were measured by the thermally induced bending technique. The stress of the metallic films, deposited by thermal evaporation (Ag and Al), is tensile, while that of the amorphous films deposited by sputtering (a-Si:H, a-Ge:H, and a-GeCx:H) and by glow discharge (a-C:H) is compressive. We observed that the coefficient of thermal expansion of the tetrahedral amorphous thin films prepared in this work, as well as that of the films reported in literature, depend on the network strain. The CTE of tensile films is smaller than that of their corresponding crystalline semiconductors, but it is higher for compressive films. On the other hand, we found out that the elastic biaxial modulus of the amorphous and metallic films is systematically smaller than that of their crystalline counterparts. This behavior stands for other films reported in the literature that were prepared by different techniques and deposition conditions. These differences were attributed to the reduction of the coordination number and to the presence of defects, such as voids and dangling bonds, in amorphous films. On the other hand, columnar structure and microcrystallinity account for the reduced elasticity of the metallic films.

18 September 2006 in Applied Physics Letters
Verified
Journal Article
Closed access
MLM. M. de Lima
M. M. de Lima
MBM. Beck
M. Beck
RHR. Hey
R. Hey
PSP. V. Santos
P. V. Santos
The authors demonstrate a compact optical waveguide modulator based on a Mach-Zehnder interferometer driven by surface acoustic waves. The modulator was monolithically fabricated on GaAs with an active region length of approximately 15μm. It yields peak-to-peak modulation exceeding 90% of the average transmission and operation in the gigahertz frequency range.

24 July 2006 in Physical Review Letters
Verified
Journal Article
Closed access
PDF file
MLM. M. de Lima
M. M. de Lima
MPM. van der Poel
M. van der Poel
PSP. V. Santos
P. V. Santos
JHJ. M. Hvam
J. M. Hvam
We show that the coherent interaction between microcavity polaritons and externally stimulated acoustic phonons forms a tunable polariton superlattice with a folded energy dispersion determined by the phonon population and wavelength. Under high phonon concentration, the strong confinement of the optical and excitonic polariton components in the phonon potential creates weakly coupled polariton wires with a virtually flat energy dispersion.

19 November 2013 in Journal of Physics D: Applied Physics
Verified
Journal Article
Closed access
SAS Aškrabić
S Aškrabić
ZDZ D Dohčević-Mitrović
Z D Dohčević-Mitrović
VAV D Araújo
V D Araújo
Gabriela IonitaGabriela Ionita
Gabriela Ionita
MLM M de Lima
M M de Lima
Andres CantareroAndres Cantarero
Andres Cantarero

2 December 2003 in Journal of Applied Physics
Verified
Journal Article
Closed access
PDF file
MLM. M. de Lima
M. M. de Lima
FAF. Alsina
F. Alsina
WSW. Seidel
W. Seidel
PSP. V. Santos
P. V. Santos
Focused surface-acoustic waves (SAWs) provide a way to reach intense acoustic fields for electro- and optoacoustic applications on semiconductors. We have investigated the focusing of SAWs by interdigital transducers (IDTs) deposited on (100)-oriented GaAs substrates. The focusing IDTs have curved fingers designed to account for the acoustic anisotropy of the substrate. Different factors that affect focusing, such as the aperture angle and the configuration of the IDT fingers, were systematically addressed. We show that the focusing performance can be considerably improved by appropriate choice of the IDT metal pads, which, under appropriate conditions, create an acoustic waveguide within the IDT. We demonstrate the generation of narrow (full width at half maximum of approx 15 μm), high-frequency (0.5 GHz), continuous SAW beams with vertical displacement as high as 4 nm collimated over distances that exceed 100 μm.