30 March 2023 in Journal of Mechanical Engineering
NINational Aerospace University Kharkiv Aviation Institute
National Aerospace University Kharkiv Aviation Institute
The stress state of a homogeneous isotropic layer under the action of a spatial static external load is studied. Two circular cylindrical supports are cut into the body of the layer parallel to its borders. The supports and body of the layer are rigidly coupled. The spatial problem theory of elasticity is solved using the analytical-numerical generalized Fourier method. The layer is considered in the Cartesian coordinate system, the supports are considered in the local cylindrical coordinates. Stresses are set on the upper and lower surfaces of the layer. The supports are considered as cylindrical cavities in a layer with zero displacements set on their surfaces. Satisfying the boundary conditions on the upper and lower surfaces of the layer, as well as on the cylindrical surfaces of the cavities, a system of infinite integro-algebraic equations, which are further reduced to linear algebraic ones, is obtained. An infinite system is solved by the reduction method. In the numerical studies, the parameters of integration oscillatory functions are analyzed, problems at different distances between supports are solved. A unit load in the form of a rapidly decreasing function is applied to the upper boundary between the supports. For these cases, an analysis of the stress state was performed on the surfaces of the layer between the supports and on the cylindrical surfaces in contact with the supports. The numerical analysis showed that when the distance between the supports increases, the stresses σx on the lower and upper surfaces of the layer and the stresses τρφ on the surfaces of the cavities increase. The use of the analytical-numerical method made it possible to obtain a result with an accuracy of 10-4 for stress values from 0 to 1 at the order of the system of equations m=6. As the order of the system increases, the accuracy of fulfilling the boundary conditions will increase. The presented analytical-numerical solution can be used for high-precision determination of the stress-strain state of the presented problems type, as well a reference for problems based on numerical methods
30 June 2022 in Journal of Mechanical Engineering
NINational Aerospace University Kharkiv Aviation Institute
National Aerospace University Kharkiv Aviation Institute
The spatial problem of the elasticity theory is studied for a layer with two infinite circular solid cylindrical inclusions that are parallel to each other and to the layer boundaries. The physical characteristics of the layer and the inclusions are different from each other and they are homogeneous, isotropic materials. The spatial function of stresses is given at the upper boundary, and the function of displacements is given at the lower layer boundary. Circular cylindrical elastic inclusions are rigidly connected to the layer. It is necessary to determine the stress-strain state of the composite body. The problem solution is based on the generalized Fourier method, which uses special formulas for the transition between the basic solutions of the Lamé equation in different coordinate systems. Thus, the layer is considered in the Cartesian coordinate system, the inclusions – in the local cylindrical ones. Satisfying the boundary and conjugation conditions, systems of infinite integro-algebraic equations were obtained, which were subsequently reduced to linear algebraic ones. The resulting infinite system is solved by the reduction method. After deter-mining the unknowns, it is possible to find the stress values at any point of the elastic composite body. In numerical studies, a comparative analysis of the stress state in the layer and on the surfaces of inclusions at different distances between them is carried out. The analysis showed that when the inclusions approach each other, the stress state in the layer practically does not change. However, its significant change is observed in the bodies of inclusions, so with dense reinforcement ((R1 + R2) / L > 0.5), it is necessary to take into account the distances be-tween the reinforcing fibers. At stress values from 0 to 1 and the order of the system of equations m=10, the accuracy of meeting the boundary conditions was 10-4. With an increase in the system order, the accuracy of meeting the boundary conditions will increase. The given analytical-numerical solution can be used for high-precision determination of the stress-strain state of the given type of problems, and also as a reference for problems based on numerical methods.
30 September 2024 in Journal of Mechanical Engineering
NINational Aerospace University Kharkiv Aviation Institute
National Aerospace University Kharkiv Aviation Institute
At the stage of designing thin-walled aircraft structures, to simplify calculations, their cross sections are idealized. To do this, the section with the skin and the longitudinal elements reinforcing it is replaced (when determining normal stresses) by a discrete one, consisting of concentrated areas at characteristic points. In this case, the equality of the moments of inertia of the initial and discrete sections is preserved. Such idealization is used in the calculation of thin-walled rods for normal and shear stresses (Wagner model). For sections consisting of a system of rectangular strips of constant thickness, discretization allows to set approximate values of normal and shear stresses and accurately find the locations of the singular points of the bending center (in an open contour) and the center of rigidity (in a closed one). The discrete model of a strip consists of three lumped areas: two at the edges and one in the center. The paper proposes to extend the discrete model to sections in which the skin thickness changes according to a linear law. In addition to the rectangular strip, it is possible to use elongated triangles and trapezoids, replaced by three and four concentrated areas, respectively. The possibility of using a discrete model for calculating some thin-walled sections of open and closed contours is considered. The section of an open contour is studied - the problem of transverse bending without torsion of a channel having flanges with a linearly variable thickness. Differences in the flows of tangential forces calculated from the exact and discrete models are shown. The coincidence of the results in determining the position of the bending center according to two models was established. When studying the application of a discrete model to a closed contour, its simplified option is proposed. The problem of transverse bending without torsion and finding the center of rigidity in a section with a contour line in the form of a trapezoid with front and rear walls of constant thickness and upper and lower skins and a similar section with a contour in the form of a rectangle was considered. Differences in the flows of tangential forces calculated by exact and discrete models are established. For a closed section in the form of a rectangle, the decrease in the moment of inertia for torsion due to the redistribution of material in the cross section was studied separately. It has been established that when finding the position of the center of rigidity, the discrepancy between the results of the exact and discrete models in sections with geometric parameters close to real ones was less than 1% for a rectangular contour, and 4% for a trapezoidal contour. The results indicate the possibility of extending the application of the discrete model of thin-walled cross section to the design calculations of thin-walled rods with variable skin thickness, representing practical structures.
30 September 2023 in Journal of Mechanical Engineering
N"National Aerospace University "
National Aerospace University "
KIKharkiv Aviation Institute
Kharkiv Aviation Institute
NINational Aerospace University "Kharkiv Aviation Institute
National Aerospace University "Kharkiv Aviation Institute
+1
This paper is dedicated to ensuring the strength of cargo equipment elements of transport aircraft. The strength of rollers of roller conveyors, which are made of standard pressed aluminum tubular profiles or composite tubular elements, is considered. The main disadvantage of these semi-finished products is the deviation of the diameter of these standard aluminum profiles, which leads to the emergence of eccentricity Δ between the axes of the outer and inner surfaces. The influence of eccentricity on the change in the values of normal and tangential stresses is considered. This analysis was carried out for standard diameters of tubular profiles at values Δ equal to half of the standard limit deviation of the outer diameter D. Calculations of normal and tangential stresses and their comparison with nominal stresses that occur in the absence of misalignment have been carried out. Calculations were made of the value c of the removal of the center of rigidity from the center of the circle of the outer border of the cross-section at different cross-section sizes of standard profiles with values of Δ equal to half of the standard limit deviation of the outer diameter D inclusively. The calculations showed an increase in tangential stresses τ in some cases by 64% and even by 213%. The obtained results indicate that the presence of Δ≠0 will have a negative effect on the resource of these elements. In order to eliminate the negative consequences, it is necessary to increase the requirements for the shape deviation of the tubular profiles in the input control.
30 March 2023 in Journal of Mechanical Engineering
NINational Aerospace University Kharkiv Aviation Institute
National Aerospace University Kharkiv Aviation Institute
Problem of predicting the residual service life of airplanes and helicopters is highly relevant for flight safety. In this paper, on the basis of the conducted research on the change of mechanical characteristics during materials fatigue accumulation, it is proposed to control the service life by changing the dissipative characteristics. In case of fatigue damage, the accumulative logarithmic decrement of oscillation damping δ increases to the limit maximum value δm, which corresponds to the critical length of the main fatigue crack, which leads to failure. The limit value δm can be set depending on the amount of energy spent on the development of the main fatigue crack, taking into account the dangerous part of the consumed energy. With the accumulation of fatigue damage, the growth of logarithmic decrement occurs at the expense of energy expenditure for the growth of fatigue cracks and internal friction. This is taken into account by the coefficient α, which allows to allocate a dangerous part of the energy that goes into the development of a main fatigue crack. The problem of durability prediction consists of two stages. At first, it is needed to determine δm for the critical crack length. Then, based on the two values of logarithmic decrement at the corresponding load cycles, the number of cycles to failure – to the critical length of the crack – is predicted by the Peris formula