6 April 2015 in Journal of Applied Physics
Ferroelectric HfO2-based thin films, which can exhibit ferroelectric properties down to sub-10 nm thicknesses, are a promising candidate for emerging high density memory technologies. As the ferroelectric thickness continues to shrink, the electrode-ferroelectric interface properties play an increasingly important role. We investigate the TaN interface properties on 10 nm thick Si-doped HfO2 thin films fabricated in a TaN metal-ferroelectric-metal stack which exhibit highly asymmetric ferroelectric characteristics. To understand the asymmetric behavior of the ferroelectric characteristics of the Si-doped HfO2 thin films, the chemical interface properties of sputtered TaN bottom and top electrodes are probed with x-ray photoelectron spectroscopy. Ta-O bonds at the bottom electrode interface and a significant presence of Hf-N bonds at both electrode interfaces are identified. It is shown that the chemical heterogeneity of the bottom and top electrode interfaces gives rise to an internal electric field, which causes the as-grown ferroelectric domains to preferentially polarize to screen positively charged oxygen vacancies aggregated at the oxidized bottom electrode interface. Electric field cycling is shown to reduce the internal electric field with a concomitant increase in remanent polarization and decrease in relative permittivity. Through an analysis of pulsed transient switching currents, back-switching is observed in Si-doped HfO2 thin films with pinched hysteresis loops and is shown to be influenced by the internal electric field.
1 July 2019 in APL Materials
The incorporation of In2O3 into Ga2O3 allows for tailoring of the bandgap over a wide range in (InxGa1−x)2O3, and this material is emerging as a candidate in transparent electrodes on optoelectronic devices, heterostructure transistors, photodetectors, and gas sensors. We have measured the band alignments for atomic layer deposited SiO2 and Al2O3 over the composition range x = 0.25–0.74 for (InxGa1−x)2O3 grown by pulsed laser deposition. The valence band offsets from 1.95 to 2.30 eV for SiO2 and 0.88 to 1.23 eV for Al2O3 over this composition range. The bandgaps of (InxGa1−x)2O3 spanned from 4.55 to 4.05 for x = 0.74–0.25. This led to nested band alignments for SiO2 and Al2O3 for the entire composition range of (InxGa1−x)2O3 investigated.
15 September 2006 in Journal of Applied Physics
The diffusion barrier properties of and Hf–Ge–N thin films for Cu metallization on Ge are examined. The diffusion barrier films were deposited by reactive sputtering on -Ge (001) single crystal substrates with varying thicknesses. Cu thin films were then deposited in situ on the diffusion barrier. The multilayer film structure was subsequently annealed in an Ar atmosphere. X-ray diffraction was used to determine the film crystallinity and identify intermetallic phases due to reactions involving the film and substrate. The and Hf–Ge–N diffusion barrier films remained amorphous for annealing temperatures up to . At thickness of , the films showed superior diffusion barrier properties as compared to Hf–Ge–N based on the appearance of secondary phases due to reactions and changes in the Cu morphology. These results suggest that is an effective barrier material for Cu integration on Ge.
1 July 1999 in Journal of Vacuum Science & Technology A
NiFe and NiFeCo thin films have been etched in and inductively coupled plasmas as a function of pressure, source power, and rf chuck power. The etch rates decrease with increasing pressure, and go through a maximum with both source and chuck power. The results are consistent with a mechanism involving ion-assisted desorption of relatively involatile etch products, and a balance of ion flux, ion energy, and chlorine neutral density is necessary to achieve practical etch rates and smooth surfaces. Under our conditions, provided the best surface morphologies and the least residual chlorine.
8 February 2014 in Applied Surface Science