In this study, a 1550 nm coherent high-spectral-resolution lidar (CHSRL) is developed to measure the optical properties of aerosols and atmospheric wind profiles in the atmospheric boundary layer. To determine the optical properties, a coherent frequency discriminator based on the fast Fourier transform is designed in the CHSRL to separate the Mie and the Rayleigh–Brillouin backscatter spectra to fulfill the needs of high-spectral measurements. The atmospheric wind velocity is retrieved using the simultaneously measured Doppler shift. This non-optical frequency discriminator is a feasible and low-cost solution compared to a narrow-bandwidth optical filter, such as a Fabry–Perot interferometer or an atomic filter. However, shot, amplifier spontaneous emission, and detector noise interfere with the Rayleigh–Brillouin spectrum. Therefore, a spectrum correction algorithm is proposed to recover the interfered Rayleigh–Brillouin spectrum, and the measurement results of the spectral line agree well with those modeled with Tenti S6 at different central frequencies. Finally, field observations for comparison are conducted with the co-located CHSRL, Raman lidar, and coherent Doppler wind lidar. The comparison results indicate that the correlation coefficient of the aerosol backscatter coefficient is 0.84. The correlation coefficient and standard deviation of wind velocity are 0.98 and 0.13 m · s−1, respectively.
The atmospheric environment monitoring satellite (DQ-1) was launched in April 2022, carrying the aerosol and carbon dioxide detection lidar (ACDL) as its primary payload. Following background characterization and nighttime calibration, daytime calibration became necessary because strong solar background radiation and thermal effects complicate daytime observations. This study presents a daytime calibration method for the ACDL 532 nm polarization and high-spectral-resolution channels based on spatiotemporally matched day-night attenuated scattering ratios. Compared with conventional weekly averaging strategies, the proposed method reduces aerosol-related errors caused by prolonged data accumulation. The theoretical systematic uncertainty is about ±7% for the polarization channels and ±6% for the high-spectral-resolution channel. Verification using clear-sky scattering-ratio tests and comparisons with CALIOP observations demonstrates that the mean clear-sky scattering ratio is approximately 1.00, remaining within the theoretical uncertainty range (1±0.11). In addition, the relative difference between ACDL and CALIOP is generally less than 10% below 25 km, confirming the effectiveness and reliability of the proposed daytime calibration method for ACDL daytime observations.
22 August 2025 in IEEE Transactions on Geoscience and Remote Sensing
The Ice, Cloud and land elevation Satellite-2 (ICESat-2) carries the new generation photon-counting lidar payload, the Advanced Topographic Laser Altimeter System (ATLAS). After after-pulse correction, the water column profile acquired by ATLAS can be used to derive vertical profiles of ocean optical parameters. However, the stability and robustness of the correction method across different sea areas could be improved. This study analyzes the broadening effect of sea surface signals caused by varying sea states. It employs land signals with broadening characteristics similar to those of the sea surface as the system impulse response function (SIRF) to perform after-pulse correction on water column profiles. By matching pulse widths, the proposed algorithm reduces the impact of sea surface broadening on after-pulse correction results. Internal consistency validation among ATLAS three strong beams is conducted and achieve the correlation coefficient exceeding 0.8 in the Black Sea, Atlantic Ocean, and Pacific Ocean. Meanwhile, the ocean optical parameter inversions are compared and validated with MODIS and BGC-Argo data. The mean relative errors of inversion results in the three sea areas are approximately 20%, representing a reduction of over 30% compared to traditional algorithm. Finally, a sensitivity analysis of the broadening matching algorithm and cumulative length confirms the algorithm’s robustness. The ocean optical parameters inversion algorithm based on pulse broadening matching lays the foundation for high-precision inversion of parameters such as chlorophyll concentration and provides a reference for future data processing in related systems.
30 April 2026 in IEEE Transactions on Geoscience and Remote Sensing
Photon-counting (PC) LiDAR, characterizing single-photon sensitivity and precise timing, plays a critical role in long-range detection, 3D imaging and spaceborne mission such as The Ice, Cloud, and land Elevation Satellite-2 (ICESat-2). However, its performance is constrained by the use of a fixed number of accumulated detections causing inefficient resource allocation in complex environment. Specifically, under high photon contrast, it leads to redundant time consumption or degraded spatial resolutions, whereas under low photon contrast, it cannot attain statistically sufficient photon events for signal discrimination. Moreover, a theoretical foundation for the minimum cumulative detection count remains underdeveloped. To address this issue, this paper develops a statistical model to determine the minimum detection count under various photon contrast conditions. The model is derived based on binomial and normal distributions, and further extended to multi-channel detection systems and complex scenarios involving photon contrast constraints. Validation via Monte Carlo simulations and experiments shows close agreement with theory, with absolute errors within 2.4% (simulation) and 1.79% (experiment), and a maximum deviation below 5%. The model reduces required detections by up to 50% under high contrast while maintaining over 90% accuracy. Furthermore, when applied to a scanning imaging LiDAR system, the method improves the Structural Similarity Index Measure (SSIM) by 23% under a photon contrast constraint Q = 2, compared to conventional equal-interval scanning within equal acquisition time. This study provides a scalable framework for PC LiDAR signal processing, with strong potential for enhancing spaceborne LiDAR data processing in complex environments.