15 April 2018 in International Journal of Engineering & Technology
The results of laboratory studies confirming the possibility of preliminary separation of free grain from the stripped grain heap before it enters the threshing chamber of a combine harvester are presented. For example, it has been established that the maximum free grain passage through the holes of the lath bottom is 68, 7% with a width of its holes of 8 mm and a length of 160 mm. The length increase of the lath bottom of the inclined chamber of the combine harvester up to 1182 mm ensures a complete separation of grain from the heap and exclude the possibility of its falling into the threshing chamber.
8 July 2022 in Tractors and Agricultural Machinery
SUBJECT OF THE STUDY: Is the process of preliminary separation of loose grains from combed grain heap on the slatted bottom of the feed elevator of a combine harvester. AIMS: Is an efficiency evaluation of the combed grain heap separation on the slatted bottom of the inclined chamber of a combine harvester in the field and to compare the degree of crushing of free grain depending on its supply to the threshing device or directly to the cleaning system. METHODS: All studies were carried out on winter wheat of the Moskovskaya 56 variety with a yield of 30 c/ha. Plant height varied within 0,60,9 m with a grain ripeness of at least 98% and a moisture content of 14%. The serial grain header ZHO-5 OZON manufactured by PJSC Penzmash was aggregated by the Niva-Effect combine harvester with a constant speed of 8 km/h and a stripping cylinder speed of 485 min-1. The field experiments were divided into two stages. The first series of experiments was devoted to evaluating the efficiency of preliminary separation of combed grain heap on the slatted bottom of the experimental feed elevator. During the second series of the experiment, grain was harvested with a serial feed elevator without its preliminary separation. RESULTS: According to the results of the first series of studies, it was found that the passage of loose grain through the holes of the slatted bottom of the inclined chamber is 91,6%. At the same time, grain crushing in the feed elevator did not exceed 0,5%, and in the bunker 1,75%. During the operation of the combine with a serial feed elevator without preliminary separation of the combed grain heap, the crushing of the bun-ker grain was within 5,25%. CONCLUSION: The practical implementation of such a technical solution makes it possible to 3 times the grain crushing in a bunker by the working bodies of the threshing machine.
30 June 2022 in Engineering Technologies and Systems
Introduction. A decrease of damaging loose grains by threshing tools when combing standing plants is an urgent scientific problem. The aim of the research is to develop a technical solution and experimentally confirm the possibility of loose grains pre-separation from the stripped grain heap before it enters the threshing chamber of the combine harvester. Materials and Methods. The most promising technical solution to minimize the damaging of loose grain is an inclined chamber containing an oblong-hole lattice bottom, under which inclined augers are mounted. The experimental studies had two stages. In the first series of experiments, in laboratory conditions there were determined the optimal sizes of the lattice bottom holes to ensure the maximum passage of loose grains. In the second series of experiments, the degrees of separating and damaging loose grains were evaluated in real field conditions. Results. According to the results of laboratory studies, it was found that the maximum passage of loose grains through the holes of the lattice bottom is 68.7% with the width of holes 8 mm and their length 160 mm. According to the results of field experiments, it was found that the average passage of loose grains through the holes of the lattice bottom is 90%. At the same time, damaging grains in the inclined chamber did not exceed 0.5%, and in the hopper 1.75%. Damaging grains in the bunker was in the range of 5.25% when the combine operated without pre-separation of the combed grain heap on the lattice bottom of the inclined chamber. Discussion and Conclusion. Pre-separation of loose grains from the combed heap makes it possible to reduce damaging grains at least three times, and also reduces the power consumed by the drive of the threshing machine by 11–12%.
28 February 2023 in SCIENCE IN THE CENTRAL RUSSIA
BUBryansk State Agrarian University
Bryansk State Agrarian University
The results of theoretical studies confirming the possibility of carrying out preliminary separation of free grain from the stripped grain pile before it enters the threshing chamber of a combine harvester are presented. The prospect of a separating device mounted directly in front of the threshing drum, consisting of longitudinal rods, over which an additional scraper conveyor is mounted, has been established. The cross section of each strip of the grating is narrowed downwards to increase the intensity of separation of the device and eliminate the possibility of clogging the holes with passing particles of the heap. The optimal length of the openings of the pre-drum type separating device, its spatial orientation were determined, and the quality indicators of the work were evaluated. Theoretical studies of the separation process on winter wheat of the “Moskovskaya 56” variety with a grain size of 3.9x6.5 mm were performed. The speed of the scraper conveyor was 3 m/s, and the angle of inclination of the separating device varied within 0-45 degrees. It has been established from the results of research that with an increase in the angle of inclination of the separating surface, the length of the sieve openings increases, and the separation speed decreases. Since the horizontal grate provides a higher separation rate of free grain, compared to an inclined surface, the use of a pre-drum type separating device is most preferable in relation to the grate bottom of the feeder house of a combine harvester in terms of its performance. It has been established that the length of the separating holes should be at least 0.08 m. Such a technical solution allows minimizing not only the crushing of free grain by the working bodies of the threshing machine, but also to reduce the metal consumption of the separating device.
24 September 2024 in Engineering Technologies and Systems
Introduction. It is possible to increase the separating of loose grain on the lattice bottom of the combine harvester feeder house by removing most of the light impurities from the combed heap using an inertial cleaning system built into the combing adapter body.Aim of the Study. The study is aimed at developing an inertial system for separating light impurities in the combing header body and optimizing its main parameters.Materials and Methods. The object of the study was a large-scale model of a pneumatic cleaning device to simulate the motion of air and components of a combed grain heap inside the combing adapter body. It was a two-factor experiment with three variations of the air flow velocity (4.5; 5.5; 6.5 m/s) and the width of the air channel (0.26; 0.29; 0.32 m). The studies were conducted on a combed heap of Moskovskaya 56 wheat with a moisture content of about 12%. As a parameter for optimization and response function, a portion of the combed heap was selected from the body of the installation with an air flow.Results. According to the results of the experimental studies, it was found that the air flow velocity has a greater effect on separating glumes than the width of the air channel. A simultaneous increase in both factors leads to an improved separation. At the same time, if increasing the air flow velocity ensures a stable increase in the proportion of the combed heap and is limited only by the air velocity at which grain appears in the combed heap along with the glumes, then changing the channel width allows achieving the parameter optimal value.Discussion and Conclusions. The use of an inertial cleaning system makes it possible to remove almost completely light impurities from the combed heap. The optimal parameters of the device are: channel width 0.28...0.3 m, air flow velocity 6...6.5 m/s.
29 March 2024 in Engineering Technologies and Systems
A highly topical scientific and practical task is to justify the choice of the most advanced variant of the device for pre-separating the combed heap and to optimize its design.