Arild Holm Clausen

Arild Holm Clausen

Auto-generated profile, based on publicly available information

Arild Holm Clausen

Structural Impact Laboratory (SIMLab), Department of Structural Engineering, Norwegian University of Science and Technology (NTNU), NO-7491 Trondheim, Norway

Research Focus & Metrics

Academic Career Length

28Years (1999-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 March 2019 in Journal of the Mechanics and Physics of Solids
Verified
Journal Article
Closed access
JJJoakim Johnsen
Joakim Johnsen
ACArild Holm Clausen
Arild Holm Clausen
FGFrode Grytten
Frode Grytten
ABAhmed Benallal
Ahmed Benallal
OHOdd Sture Hopperstad
Odd Sture Hopperstad

1 December 2015 in International Journal of Impact Engineering
Verified
Journal Article
Closed access
VVV. Vilamosa
V. Vilamosa
ACA.H. Clausen
A.H. Clausen
TBT. Børvik
T. Børvik
SSS.R. Skjervold
S.R. Skjervold
OHO.S. Hopperstad
O.S. Hopperstad

1 August 2016 in Polymer Testing
Verified
Journal Article
Closed access
JJJoakim Johnsen
Joakim Johnsen
FGFrode Grytten
Frode Grytten
OHOdd Sture Hopperstad
Odd Sture Hopperstad
ACArild Holm Clausen
Arild Holm Clausen

1 March 2017 in Mechanics of Materials
Verified
Journal Article
Closed access
AIArne Ilseng
Arne Ilseng
BSBjørn H. Skallerud
Bjørn H. Skallerud
ACArild H. Clausen
Arild H. Clausen

1 April 1999 in Journal of Engineering Mechanics
Verified
Journal Article
Closed access
ACArild H. Clausen
Arild H. Clausen
OHOdd S. Hopperstad
Odd S. Hopperstad
MLMagnus Langseth
Magnus Langseth
An experimental stretch bending study is presented in this paper. A total of 24 tests on 2-m-long rectangular hollow section aluminum specimens are performed in a specially designed stretch bending rig. All tests are carried out with a constant tensile force corresponding to the material's yield stress. Factorial analysis is systematically used in the planning of the experimental program as well as in the result interpretation. Special attention is paid to the influence of the alloy, die radius, and specimen wall thickness on certain response parameters. As stretch bending is an important industrial forming process, die force, sagging, and springback are considered to be the most relevant responses. The tests show that the alloy has the largest influence on the die force and springback, while the sagging behavior is primarily controlled by the geometric parameters (i.e., die radius and thickness).

1 May 1999 in Journal of Engineering Mechanics
Verified
Journal Article
Closed access
ACArild H. Clausen
Arild H. Clausen
OHOdd S. Hopperstad
Odd S. Hopperstad
MLMagnus Langseth
Magnus Langseth
An experimental stretch bending study is presented in this paper. A total of 29 tests on 2 m long rectangular hollow section aluminum specimens were performed in a purpose-built stretch bending rig. The tests were carried out under different tensile force combinations, or tensile sequences, in order to investigate the influence of the force on certain response parameters. Stretch bending is an important industrial forming process, and die force, sagging, and springback are thus considered the most relevant response parameters. The tests show that the sagging is very sensitive to the applied tensile sequence. Furthermore, a close correlation between sagging development and strain evolution is observed. The springback is controlled by the tensile force level immediately before unloading. Finally, the difference in response between two tests performed with different constant, tensile force levels is insignificant.