23 March 2017 in IEEE Transactions on Components, Packaging and Manufacturing Technology
The contribution of this paper is to propose novel balanced and dual-band bandpass filters (BPFs), using quarter-mode (QM) and eighth-mode (EM) substrate integrated waveguide (SIW) cavities, for the size reduction of the overall circuit. Two balanced BPFs, which separately demonstrate a third-order Chebyshev response and a fourth-order quasi-elliptic response, are realized by properly choosing, feeding, and coupling those QMSIW and EMSIW cavities. Not only desired differential-mode operation within the passband, but also good common-mode suppression in a certain frequency range have been achieved. Furthermore, a dual-band BPF with improved out-of-band rejection is also realized by properly constructing the coupling topology of four EMSIW cavities. An additional source-to-load coupling path is introduced in this dual-band BPF to obtain more transmission zeros (TZs). The sizes of resonant cavities utilized in the above designs are only one-fourth or one-eighth of those rectangular ones in conventional designs, which lead to a significant reduction in the overall circuit size. All proposed designs have been fabricated and measured to verify simulation predictions. Based on the author's knowledge, it is the first time using QMSIW and EMSIW for balanced filter designs, and dual-band filter designs with TZs.
3 May 2017 in IEEE Transactions on Components, Packaging and Manufacturing Technology
A 2×2 dual-polarized antenna subarray with filtering responses is proposed in this paper. This antenna subarray is a multilayered 3-D geometry, including a dual-path 1× 4 feeding network and four cavity-backed slot antennas. The isolation performance between two input ports is greatly improved by a novel method, which only needs to modify several vias in a square resonator. Cavities in the feeding network are properly arranged and coupled using different coupling structures, so that the operation modes in each cavity for different paths can always remain orthogonal, which enables the subarray to exhibit not only filtering functions (in both reflection coefficients and gain responses), but also a low cross-polarization level. A prototype is fabricated with a center frequency of 37 GHz and a bandwidth of 600 MHz for demonstration. Good agreement is achieved between simulation and measurement, for both S-parameter and far-field results. The proposed filtering dual-polarized antenna array is very suitable to be employed as the subarray in millimeter-wave 5G base stations to reduce the complexity and integration loss of such beamforming systems.
16 April 2018 in IEEE Antennas and Wireless Propagation Letters
A polarization-agility antenna using liquid metal (eutectic gallium indium) with high radiation efficiency is proposed in this paper. This design approach offers possibilities to use minimum amount of liquid metal as well as elastomer, so that a higher-radiation-efficiency liquid metal antenna (LMA) can be realized. The proposed design is based on an aperture-coupled patch antenna composed of both liquid metal alloy and copper tape. The polarization of this antenna is controlled by the position of the pressure-driven liquid metal encased in four triangle cavities constructed by both the elastic dielectric material (i.e. Ecoflex) and PET film. A prototype is demonstrated with a center frequency of 2.45 GHz. Three kinds of polarization including left-hand circular polarization (LHCP), right-hand circular polarization (RHCP)) and linear polarization (LP) are successfully demonstrated. A radiation efficiency higher than 90% is observed in the measurement.
16 September 2020 in IEEE Transactions on Microwave Theory and Techniques
The Doppler radar has been widely used in respiration detection. However, most of the existing microwave respiration detection works are intended for either a single human subject in front of the radar or multiple subjects with known positions. In this article, a system based on single-input-multiple-output (SIMO) continuous-wave (CW) radar equipped with adaptive digital beamforming (ADBF) technique is presented to detect the respiration of multiple human subjects at unknown positions simultaneously. A solution based on the modified Capon (m-Capon) direction-of-arrival (DOA) estimation and linear constraint minimal variance (LCMV) ADBF is proposed to automatically find the angles of human subjects. By forming spatially distributed beams toward the subjects of interest, human respiration can be remotely obtained. Furthermore, for the detection of each person's respiration, nulls are also generated at the angles of nearby interfering subjects, which results in high target discrimination capability when multiple human subjects are close to each other. The experimental results show good detection accuracy compared with the reference sensor, which verifies the effectiveness of the developed system for multitarget respiration detection.
31 August 2016 in IEEE Transactions on Components, Packaging and Manufacturing Technology
Integration design of a filtering antenna fed by a load-insensitive multimode balun bandpass filter is proposed in this paper. The balun filter is designed and realized using multilayer structure for miniaturization. To be directly integrated into the antenna, both amplitude and phase performances of the balun filter are investigated with different complex load impedances. With insensitive responses against the load, this balun filter is utilized to design a filtering antenna as the feeding of a quasi-Yagi antenna, which is considered as a frequency-dependent differential complex load. The radiation characteristics are improved by applying a metallic shield as the package for the proposed design. To verify the design concept, an experimental filtering antenna is designed, fabricated, and measured with almost the same passband as that of the balun filter benefiting from the load-insensitive property of the latter. The simulated and measured results are presented, showing good agreement.
24 November 2016 in IEEE Transactions on Antennas and Propagation
This communication describes a novel concept of designing millimeter-wave (mm-wave) dielectric resonator antenna (DRA) arrays, in which the DRA element and part of its feeding network can be codesigned and cofabricated using the printed circuit board technology. Conventionally, the DRA and its feed are designed and fabricated using different dielectric materials. As a result, a large error might take place when mounting the DRA to its feed, which will result in significant influences to the performance of the antenna, especially to those operating in the mm-wave band. The proposed concept of the substrate integrated DRA provides a possibility to minimize the above mounting errors, by shaping the DRA and its feed together using the same material and fabrication process. Two kinds of antenna element, which separately exhibits linear and circular polarization, are designed at Ka-band. In order to demonstrate the feasibility of the proposed elements for array applications, two four-element antenna arrays in cooperation with different feeding networks and transitions are also designed, fabricated, and measured. Investigations show good agreement between simulation and measurement. The proposed substrate integrated DRA array can be easily extended to larger scales and has great potential to be integrated into mm-wave transceiver modules.