8 July 2022 in IEEE Transactions on Power Electronics
Modular multilevel converter (MMC) faces challenges ofcost and footprint in medium and high voltage grid applications. By adding a three-phase switching bridge on the basis of MMC, this article proposes a three-phase multiplexing arm modular multilevel converter (TPMA-MMC) with high power density and small volume. The multiplexing principle for TPMA-MMC is investigated, showing the multiplexing arm can be multiplexed for one-third fundamental period. After that, the subsection modulation scheme is further proposed for energy balance purpose. Compared with MMC, the number of submodules (SMs) and power devices are reduced by 22.8% and 13.83%, respectively, resulting in lower construction cost. Meanwhile, the SMs’ capacitance and the total capacitor energy storage of TPMA-MMC reduce greatly with the subsection modulation, which can greatly reduce the footprint and improve the power density. Moreover, the proposed TPMA-MMC outperforms the MMC in terms of efficiency. Finally, the topology and proposed modulation scheme are verified by simulation and experimental results.
20 July 2023 in IEEE Journal of Emerging and Selected Topics in Power Electronics
Three-phase multiplexing arm modular multilevel converter (TPMA-MMC) possesses cost-efficiency advantage by employing a pair of multiplexing arms. However, the narrow multiplexing arm energy regulation period results in the limited modulation range [0.82,1]. This article proposes a wide multiplexed period operation principle with the multiplexing arm energy regulation period being extended to one-fundamental period, and with which, it realizes to expand the modulation range to [0,1]. Besides, based on it, the existing “overlap” period could also contribute to realizing the multiplexing arm energy balance in one-third fundamental period. Therefore, analysis of this new principle indicates that TPMA-MMC demonstrates some improved advantages. Compared to MMC, it reduces by 21.8% in SM count, 28.9% in operation loss, and 39.9% in energy storage, which could result in lower construction cost, footprint, and higher efficiency and power density, and the proposed principle also permits TPMA-MMC to possess higher efficiency than that with the narrow range principle. Finally, the proposed wide multiplexed period operation principle and control scheme are verified by simulation and scale-down prototype experimental results.
1 May 2023 in IEEE Journal of Emerging and Selected Topics in Power Electronics
Three-phase multiplexing arm modular multilevel converter (TPMA-MMC) possesses lower cost, smaller volume, and higher efficiency compared with MMC. However, the limited operation range limits its popularity. Hence, in this article, it redefines arm submodule (SM) configuration type, where the conventional arm is configured with full-bridge submodules (FBSMs), and the multiplexing arm is formed by half-bridge submodules (HBSMs). Meanwhile, a new energy balance principle and modulation scheme are proposed to expand TPMA-MMC’s operation range. Furthermore, the DC-fault blocking schemes could be implemented to realize DC-fault tolerance reliably without the multiplexing arm blocking. Compared with hybrid MMC(H-MMC), it could reduce by 33.33% in submodules a least, which leads lower footprint and operation loss. Due to reregulating the energy flowing path of multiplexing arm, and rearranging the chain-link voltage of multiplexing and conventional arm, it could reduce the required SM capacitance and further decrease 65% energy storage requirement, resulting in improving the power density. Finally, the topology control scheme and DC-fault blocking scheme are verified by simulation and scale-down prototype experimental results.
20 October 2025 in IEEE Transactions on Power Electronics
This article proposes a novel low-voltage ride-through (LVRT) control strategy for doubly-fed variable-speed pumped hydro storage (VS-PHS) units. Unlike conventional LVRT approaches for doubly-fed induction generators (DFIGs) that mainly rely on crowbar circuits or virtual inductance control, the proposed strategy combines rotor-side virtual inductance with dc-link voltage boosting, fully leveraging the tolerance of pumped hydro units to elevated dc-link voltages during pumping-mode self-startup. In this way, it overcomes the inherent limitations of single virtual inductance control and extends the applicable range of virtual inductance control. A real-time digital simulation platform of a 300 MW VS-PHS unit is established to validate the method. Simulation results demonstrate that the proposed strategy not only suppresses rotor overcurrent more effectively than conventional demagnetization control but also provides reactive power support during faults, offering clear advantages over existing DFIG LVRT strategies. It can still operate safely and stably under severe voltage drops of up to 80% . This ensures secure and stable operation in both generating and pumping modes, across a wide speed range and under varying fault severities.
28 November 2024 in IEEE Transactions on Power Electronics
As a power electronic device in place of normal open point, the soft open point (SOP) can improve the operating flexibility of a distribution network (DN). Most of the existing SOP projects adopt the back-to-back modular multilevel converter (BTB-MMC) topology. However, the BTB-MMC requires a large number of submodules, which is costly and bulky. In this paper, a mixed-frequency modulation based SOP (MFSOP) topology is proposed. The proposed MFSOP consists of a shunt cascaded H-bridge (CHBs), multiple series CHBs and multiple LC resonance branches. Each terminal is equipped with a Y-△ transformer to isolate the medium-frequency zero sequence voltage introduced by the mixed-frequency modulation from the power grid. Compared with the traditional BTB-MMC, the proposed MFSOP can reduce the number of submodules, which makes the SOP more compact in size. The circulating current models are derived, and two circulating current suppression strategies are proposed based on circulating current models. Then, the control strategies are described and the key parameters are designed. Finally, the correctness and validity of the proposed MFSOP are verified by simulation and experimental results.
11 April 2025 in IEEE Journal of Emerging and Selected Topics in Power Electronics
In order to adjust increased renewable energy, Soft normally open Point (SNOP) is used to increase the flexibility of AC distribution network. The back-to-back voltage source converter (BTB-VSC) is the most commonly used SNOP topology, and the current control method is that one end controls the DC voltage and the other end controls the power flow or AC voltage. However, this strategy relies on the synchronous switching of grid breakers and control modes. In this paper, an integrated control method is proposed, which treats SNOP as an equivalent series-parallel module. In the grid-connected condition, SNOP is modeled as Unified power flow controller (UPFC) for power flow control in the grid-connected scenario. However, in short circuit or islanding case, SNOP is modeled as impedance, which can effectively limit the current during short circuit and adaptively support islanding voltage in islanding case. The corresponding pre-synchronization strategy is designed during the grid-connected process and small-signal models are built to design the parameters. Finally, an experimental platform was established to verify the effectiveness of the control method under the conditions of uninterrupted transmission and grid-connected operation.