26 February 2019 in IEEE Journal of Photovoltaics
With increasing installations of photovoltaic (PV) systems, interest in power forecasting has also increased. Inaccurate forecasts would result in substantial economic losses and system reliability issues. The correlation between weather variables and PV power is critical to ensure the efficient use of energy in PV systems. A key step toward accurate power forecasting is estimating the output from a PV system based on known environmental input data. In this research, all available weather data are used to predict the PV power. Meteorological and power data are then analyzed using a statistical approach to identify the order of significance of the input variables. Then, a predictive model is suggested as a function of irradiance, ambient temperature, wind speed, and relative humidity. The model produces a root mean square error of 4.957% and a mean absolute percentage error of 5.468% during the measurement period and over the entire range of irradiation.
29 July 2019 in IEEE Journal of Photovoltaics
Unlike conventional photovoltaic (PV) modules that generate power by absorbing light through the front side only, a bifacial PV module can generate power by absorbing light through the rear as well as the front, which would lead to an enhancement of power generation. Particularly, bifacial PV modules would have the advantage of lower power loss in shaded environments than monofacial PV modules, thanks to the light absorbed through the rear side. To predict the power of a bifacial PV module in a shaded environment, modeling is suggested by considering the shaded areas, the operational status of the bypass diodes, and the temperature of the bifacial PV module. To verify the power prediction of a bifacial PV module with a shaded area, modeled and measured powers are compared, showing error rates of 7.28%. From the results of the power loss experiments for bifacial and monofacial PV modules in shaded environments, it is confirmed that the bifacial PV module shows a relatively low power loss rate when compared with the monofacial PV module, with a power loss rate being 87.26% of the rate for the monofacial PV module.
4 November 2020 in IEEE Journal of Photovoltaics
Fault detection and repair of the components of photovoltaic (PV) systems are essential to avoid economic losses and facility accidents, thereby ensuring reliable and safe systems. This article presents a method to detect faults in a PV system based on power ratio (PR), voltage ratio (VR), and current ratio (IR). The lower control limit (LCL) and upper control limit (UCL) of each ratio were defined using the data of a test site system under normal operating conditions. If PR exceeded the set range, the algorithm considered a fault. Subsequently, PR and IR were examined via the algorithm to diagnose faults in the system as series, parallel, or total faults. The results showed that PR exceeded the designated range between LCL (0.93) and UCL (1.02) by dropping to 0.91–0.68, 0.88–0.62, and 0.66–0.33 for series, total, and parallel faults, respectively. Moreover, VR exceeded the LCL (0.99) and UCL (1.01) by 0.95–0.69 and 0.91–0.62 for series and total faults, respectively, but not under parallel faults condition. IR did not change in series and total faults but exceeded the range of LCL (0.93) and UCL (1.05) by dropping to 0.66–0.33. Thus, faults in PV systems can be detected and diagnosed by analyzing quantitative output values.
16 August 2018 in IEEE Access
A distributed power generation system uses an intermittent power source that provides low power. Furthermore, it cannot be centrally controlled from the perspective of the system operator. The photovoltaic (PV) power generation system is installed with an energy storage system (ESS) to increase the power source quality compared to that possible with PV-only power generation. In this paper, an estimation algorithm is proposed for improving battery capacity to construct a suitable and economical system. In addition, an optimal algorithm is proposed that considers different factors. For example, the cost of constructing the battery and the amount of electric power sales reflecting the renewable energy certificate weighting factor of 5.0 are based on the cost of the battery construction, depth of battery discharge, charge/discharge cycle of the battery, cost of the energy conversion device, operation maintenance cost, and charge cycle of the battery. The optimized battery capacity is calculated by considering the correlation between PV power and meteorological parameters, construction cost, and the benefit of the amount of electricity sold, with an error rate of 5.75%.