An improved recycling folded cascode operational transconductance amplifier with gain boosting and enhanced phase-margin is proposed. Among four variants of folded cascode amplifiers that have been implemented in TSMC 0.18μm CMOS process under same power and area constraints, the proposed amplifier achieves the lowest settling error of less than 0.5% compared to 1.1% settling error by Improved Recycling Folded Cascode (IRFC), 1.4% settling error by Recycling Folded Cascode (RFC) and 30% settling error by conventional Folded Cascode (FC) amplifier. This performance enhancement is attributed to 30dB increment in low-frequency gain and 7° improvement in the phase margin when compared with the second best performing Improved Recycling Folded Cascode amplifier.
This letter presents a three-dimensional (3D) integrated Molybdenum (Mo) Thermoresistive Micro Calorimetric Flow (TMCF) sensor in a 0.18 μm CMOS MEMS technology. The sensor consists of a MEMS structure which is fabricated inside a sealed micro channel and a constant temperature (CT) control circuit implemented on the CMOS wafer. The MEMS structure and CMOS circuit are 3D integrated at the wafer level. For the N2 gas flow, the proposed flow sensor achieves a high sensitivity of 0.71 mV/(m/s) and a wide bidirectional detection ability of -26 ~ 26 m/s. Moreover, an Equivalent Circuit Model (ECM) is proposed in this letter, which depicts the nonlinear output/overheated temperature (Vout/μTh) sensor response to the input gas flow. This model would be an efficient tool for the design and optimization of high-performance System on Chip (SoC) calorimetric flow sensors.
We present an integrated complimentary metal-oxide-semiconductor (CMOS) MEMS flow sensor, which demonstrates a very compact system on chip (SoC) that can sense N 2 gas flow ranging from 0 to 26 m/s (0-50 sccm). Implemented in the proprietary InvenSense AlN process, our SoC features a very low-power current feedback instrumentation amplifier (CFIA) as a front-end readout circuit for a micro-calorimetric flow sensor configured in a Wheatstone bridge. To maintain a constant temperature difference of 56 K, an on-chip heater with off-chip op-amp feedback circuit is also implemented. The on-chip CFIA is chopped at 50 kHz to reduce its offset and flicker-noise and consumes 250 μA current. The measured sensitivity of our CMOS MEMS flow sensor is 35 mV/sccm.
In this paper, we presented a wafer-level encapsulated Thermoresistive Micro Calorimetric Flow (TMCF) sensor with the integrated packaging by using the proprietary InvenSense CMOS MEMS technology. For the nitrogen gas flow from -26m/s to 26m/s, the pulsed operated TMCF sensor (device size = 3.4mm2) under the Constant Temperature Difference (CTD) mode achieved a normalized sensitivity of 112.4μV/(m/s)/mW with respect to the input heating power. Besides, the measured TMCF sensor response time (τmax<;3.63ms) shows good agreement with a theoretical model. With the pulsed operation, the proposed low-power TMCF sensor will be a promising digital CMOS MEMS flow sensor for the Internet of Things (IoT), especially for smart building/home.
In this paper, we report a wireless dual-mode micro thermal flow (DMTF) sensor system with the extended flow range by using InvenSense 0.18μm CMOS MEMS technology. For the N 2 gas flow, the DMTF sensor gains a flow range of 0~73m/s, which is 2.4 times larger than that of calorimetric flow sensor (0~31m/s) setup. Besides, the calibrated DMTF sensor system shows an accuracy of less than 2% with the wireless monitoring capability. Therefore, this low-cost wireless DMTF sensor system will be a promising IoT (Internet of Things) device for the smart energy-efficient buildings application.