Nowadays, humidity sensors have become essential in numerous applications. However, there are several problems while using them for humidity detection, such as low sensitivity, delayed response and recovery times, less stability, and narrow humidity detection ranges. Here, we demonstrate for the first time a highly sensitive chemiresistive sensor for low-level humidity detection in ambient atmosphere by introducing graphene oxide (GO) and doped GO (Li-doped GO and B-doped GO) as a thin film in a facile manner. The sensitivity, repeatability, and stability studies show that thin film-based fabricated humidity sensors are unprecedently efficient in the detection of different percentages of humidity from 11 to 97% at room temperature. The incorporation of doping into GO induces a dramatic change in the sensing behavior of the base film (undoped GO). This allows the sensor to be used in a variety of applications such as humidity sensing, which we validate through our experiment with a “cheap and readily available” recognition system.
The arch-shaped single electrode based triboelectric nanogenerator (TENG) is fabricated using thin film of reduced graphene oxide nanoribbons (rGONRs) with polyvinylidene fluoride (PVDF) polymer used as binder to effectively convert mechanical energy into electrical energy. The incorporation of rGONRs in PVDF polymer enhances average surface roughness of rGONRs/PVDF thin film. With the combination of the enhancement of average roughness and production of functional groups, which indicate improve charge storage capacity of prepared film. Furthermore, the redox peaks obtained through cyclic voltammetry were identified more in rGONRs/PVDF composite in comparison to pristine rGONRs to confirm charge transfer capability of film. Herein, the output performance was discussed experimentally as well as theoretically, maximum voltage was obtained to be 0.35 V. The newly designed TENG to harvest mechanical energy and opens up many new avenues of research in the energy harvesting applications.
In this work, a selective chemiresistive gas sensor for carbon dioxide gas detection at room temperature (∼25 °C) was successfully fabricated, where ruthenium-decorated tungsten disulfide (Ru@WS 2 ) quantum dots (QDs) have been used as the sensing material. A mixed solvent of lithium hydroxide (LiOH · H 2 O) and N-methyl-2-pyrrolidone (NMP) was used to obtain the Ru-decorated WS 2 QDs from the exfoliated WS 2 nanoflakes. Then, the prepared WS 2 QDs and Ru@WS 2 QDs were confirmed using different material characterization techniques. The gas sensors were prepared by spraying the WS 2 QDs and Ru@WS 2 QDs on gold interdigitated electrodes (IDE), and were then exposed to various concentrations of CO 2 gas in dry air conditions. Also, the effect of humidity on both sensors in 5000 ppm CO 2 gas has been studied. The Ru@WS 2 QD based sensor showed superior sensitivity and good selectivity to CO 2 gas in comparison with isopropanol, acetone, ethanol, methanol and benzene at room temperature than the WS 2 QD. The sensor showed an increase in resistance when exposed to CO 2 gas ranging from 500 to 5000 ppm, indicating p-type characteristics. The Ru@WS 2 QD shows less effects at different humid conditions compared to WS 2 QD as a CO 2 gas sensor.
A class of highly sensitive chemiresistive sensors is developed for methanol (MeOH) vapor detection in ambient atmosphere by introducing conductive nanofillers like carbon black, multi-wall carbon nanotubes, and reduced graphene oxide into sulfonated poly(etherimide) (PEI)/liquid crystal polymer (LCP) composite (sPEI-LCP). Polar composites are prepared by a sulfonation process for instantaneous enhancement in adsorption capability of the sensing films to the target analyte (MeOH). Sensing properties exhibit that polymer composite-based fabricated sensors are efficient for the detection of different concentration of methanol vapor from 300–1200 parts-per-million (ppm) at room temperature. The incorporation of nanofiller induces the dramatic change in sensing behavior of base composite film (sPEI-LCP). Thus, less mass fraction of nanofillers (i.e. 2 wt%) influences the nonlinear sensing behavior for the entire range of methanol vapor. The simple method and low fabrication cost of the prepared sensor are compelling reasons that methanol vapor sensor is suitable for environmental monitoring.
2 October 2025 in Journal of Materials Chemistry A
Our research demonstrates a one-step dual-process acid treatment approach for modifying graphite, which increases its interlayer distance and generates nanoscale holes, thereby effectively shortening the lithium-ion diffusion pathway without the need for heteroatom doping. Compared with pristine graphite (PG), the expanded holey graphite (EG) produced by this process achieves significantly enhanced electrochemical performance while maintaining structural integrity. The EG shows excellent electrochemical performance, reaching a specific capacity of 179.45 mAh g−1 and retaining 89.3% of its capacity after 300 cycles in a full pouch cell combined with a commercial NMC523 cathode. High coulombic efficiency (approximately 93.8%) and improved cycling stability confirm the durability of the etched graphite. Beyond mere performance considerations, the study elucidates the degradation mechanisms inherent in commercial lithium-ion batteries (LIBs), thereby offering dependable guidance for electrode surface engineering and the optimization of cycling protocols. With this scalable and impurity-free approach to modification, purified etched graphite emerges as a promising candidate for next-generation LIB anodes, satisfying the high energy requirements and durability necessary for electric vehicles and advanced energy storage systems.