16 March 2020 in IEEE Transactions on Instrumentation and Measurement
Blade tip timing (BTT) is an effective non-contact measurement technology for rotating blade health monitoring. However, due to the mismatching between the high-speed rotation and the limited amount of probes, the signal collected from BTT system is severely under-sampled, which induces the difficulty in feature extraction. Multiple signal classification (MUSIC) has the potential to overcome the under-sampled problem once the probes are properly placed. Whereas, if traditional MUSIC is directly used in BTT, the accuracy of frequency identification cannot be high enough and the identified numbers of frequency components are also severely restrained. To address these two problems, an improved MUSIC is proposed as an alternative methodology to extract the blade vibration frequency for BTT. Based on the orthogonality of the signal subspace and the noise subspace from under-sampled signal, the presented method can effectively identify the vibration frequency components from the under-sampled signal of BTT.
12 April 2022 in IEEE Transactions on Industrial Electronics
Rotating blades are key turbomachinery components with high failure risk due to harsh working conditions. Thus, monitoring the running state of blades is urgently required. Blade tip timing (BTT) is regarded as a potential technology for blade vibration monitoring owing to its noncontact nature and low cost. However, severe undersampling and strict probe layout hinder the application of BTT. As a result of severe undersampling, aliasing and its suppression are the main research topics in BTT. However, in this article, a biprobes method for BTT based on the utilization of aliasing is proposed to identify the natural frequencies of blades. Active aliasing is used in this method to produce aliasing findings at various equivalent sampling frequencies, and the closed-form robust Chinese remainder theorem is used for dealiasing. Unlike the conventional multirate sampling systems for BTT that use a multiprobe configuration or varied speed, the suggested method utilizes varying delay durations to obtain varying equivalent sample frequencies. Furthermore, to ensure that active aliasing and dealiasing form a closed loop, an included angle coprime layout is proposed. Finally, the robustness and effectiveness of the proposed method are verified through numerical and experimental validation.
8 March 2022 in IEEE Transactions on Instrumentation and Measurement
The rotor blade is the core turbomachinery component with high failure risk. Thus, condition monitoring of blades is critical to ensure engine safety. Blade tip timing (BTT) is one of the most promising approaches to measure vibration, which is used for monitoring the health of blades. In reality, blade displacement contains several unwanted components that cause measurement uncertainty. However, because undersampling leads to spectrum aliasing, and the aliasing frequency changes with speed fluctuation, conventional filtering techniques fail to remove the portion of the signal that causes uncertainty. In this work, two filtering methods for the BTT signal are proposed based on sampling aliasing frequency (SAFE) map, namely, single-probe data detrending and tracking sliding bandpass filtering, which can extract synchronous vibration and denoise the reserved signal (asynchronous vibration) due to the clear distribution of different components in the SAFE map. The former eliminates the rotation frequency and its harmonic components by detrending of the BTT signal, whereas the latter effectively reduces the noise of the BTT signal by bandpass filters whose limit frequencies are adjusted according to sampling frequency and the trajectory in the SAFE map. Furthermore, the time-domain signal and the spectrum obtained by the orthogonal matching pursuit (OMP) algorithm are used to show the filtering effect. The effectiveness and interpretability of the proposed method are verified by simulation and experimental data.
15 September 2021 in IEEE Transactions on Instrumentation and Measurement
Blades are weak and essential parts of an aeroengine. Monitoring the running state of blades is essential for ensuring the safety of aeroengine operation. Blade tip timing (BTT) is considered a promising technique for operational blade vibration monitoring for turbomachinery; however, it is difficult to analyze the BTT signal because of the inherent undersampled limitation. To overcome this limitation, the minimal sensor layout scheme is restricted to be “three.” Usually, more than five probes are required for good signal revolution. This requirement is an installation restriction that limits the application of BTT; however, for users, the conflict between probe layout optimization and real installation restriction is also a serious problem. Motivated by these issues, a single-probe BTT (SP-BTT) method is proposed; the SP-BTT method could extract the shift between natural frequencies, which could be used as a damage index for blade condition monitoring. To validate the effectiveness of the proposed method, numerical simulations and experimental tests are performed.
4 January 2021 in IEEE Transactions on Instrumentation and Measurement
The harsh working environment of compressor threats the integrality of bladed disk. Crack is one of the most fatal faults of rotating blades. Detecting the crack of blades at early stage could ensure the safe operation of gas turbine and save economic costs. Blade tip timing (BTT) is a noncontact blade vibration measurement technique, which is widely used in recent years. In this article, a procedure of crack detection using BTT data is proposed. First, some typical parameters are taken into consideration, including resonance frequency, amplitude change of natural frequency, amplitude of blade tip, phase, and interblade spacing. It has been found that the frequency of the blade will decrease with the increment of crack length and reduction of crack height. In addition, the resonance frequency of the bladed disk will split when the blade cracks. The amplitude of different orders of resonance frequency varies with cracks. The amplitude of the first order changes very slightly, whereas the second and third orders are relatively obvious. The blade tip vibration amplitude and phase change with cracks without obvious regularity. The interblade distance will change due to the appearance of cracks. According to the above rules, the frequency and the interblade distance are adopted as crack diagnosis indicators. First, we use the Lomb-Scargle periodogram to quickly determine whether the crack appears and then use the blade frequency and interblade distance to locate the number of the blade having crack. In the experimental test, BTT data measured on a titanium bladed disk is used to verify the effectiveness of our method.
25 August 2021 in IEEE Transactions on Instrumentation and Measurement
Blade health monitoring (BHM) is an important technology to ensure safe operation of turbine machinery. The blade tip timing (BTT) method is a non-contact approach of vibration monitoring that is widely used for aero-engines. A BTT signal can be characterized as nonuniform and sub-Nyquist sampled (i.e., under-sampled). For nonuniform sampling, the least squares (LS) fitting method has long been used to reconstruct the spectrum. However, the under-sampling of the BTT signal causes the spectrum obtained by LS fitting aliasing. The iterative reweighted LS periodogram (IRLSP) can eliminate the aliasing caused by sub-Nyquist and nonuniform sampling. This method weakens the frequency aliasing through the method of reweighted iteration, but the consequence of this operation is that the amount of calculation is greatly increased. Thus, we propose an adaptive iterative approach (AIA) based on the IRLSP that combines a priori information of the blade. The main contribution of this method is to improve the computational efficiency for processing the BTT signal and the effect of anti-aliasing. These two points mean that this method is expected to become a real-time blade vibration monitoring method. We combined a finite element model with modal testing to perform simulations and verify the improvement with AIA. A large number of experiments were also performed to verify the effectiveness of our approach for BHM.