1 February 2023 in Flexible and Printed Electronics
In this article, we report the development of a new method for the 3D printing of dielectrics. An aerosol-jet printer is used to deposit overlapping layers of photopolymer material under ultraviolet floodlight in the assembly of ramping microstructures in situ without the need for supporting structures. Printing is conducted using an in-house photodielectric ink, the development of which is presented with an emphasis on dielectric and mechanical bulk material characterization. Low dielectric loss at the X-band and structural strength are demonstrated, followed by print characterization wherein the driving mechanisms of the new method are explored, tied to print conditions, and related to specific material properties. Finally, a complex structure in the form of a 3D flower is printed to demonstrate the controlled and repeatable performance of the proposed technique.
11 March 2025 in Advanced Engineering Materials
Additively manufactured high‐frequency electronics have the potential to feature prominently in the ongoing communications revolution by delivering previously unattainable levels of circuit miniaturization, weight reduction, and conformal and flexible circuitization. However, lack of process optimization has hampered adoption. Specifically, printed conductor surface roughness remains underexplored. Conductor roughness leads to increased loss, which worsens as frequency increases. Despite being studied rigorously with conventional copper conductors, printed roughness is largely ignored. In fact, figures for printed transmission line loss are reported, which exceed simulations because ideal roughness is assumed. Here, process‐induced roughness in aerosol‐jet printed (AJP) transmission lines is analyzed. AJP is used extensively given its resolution, but unique processing artifacts result in roughness profiles dissimilar from conventional copper. Therefore, different existing electromagnetic models are evaluated for simulating printed transmission lines with practical roughness. Subsequently, to demonstrate the influence of roughness on printed electronics, simulations are built to predict the performance of AJP transmission lines and interconnects with varying roughness. Finally, we explore process‐induced surface roughness in AJP in situ UV‐cured dielectrics and silver nanoparticle conductors via the fabrication of AJP transmission lines is explored to minimize AJP roughness with these material types by optimizing platen temperature and in situ UV cure intensity, respectively.
5 August 2025 in Advanced Engineering Materials
6 May 2025 in IEEE Transactions on Microwave Theory and Techniques
This work presents a novel exploration of the performance and reliability of 3-D printed interconnects for high-power radio frequency (RF) and microwave applications. Material studies are performed to validate aerosol-jet printed (AJP) interconnects under high-power direct-current (dc) and RF excitation before demonstration in the additive integration of a 19-W high-power amplifier (HPA). First, printed interconnects of various widths are tested under continuous-wave (CW) dc conditions, with traces as narrow as $50~\mu $ m shown to support loads of up to 25 W. Then, printed interconnects are tested at 10 W under pulsed RF conditions of varying pulsewidth and duty cycle. Thermogravimetric analysis (TGA) is used to optimize thermal sintering of the silver nanoparticle printed interconnects and minimize deltas due to part failure or further sintering under high-power loads. Finally, a bare die microwave monolithic integrated circuit (MMIC) HPA is integrated using AJP conductors and novel airgap AJP dielectric filets. Small-signal measurements show about 20-dB nominal gain and 15-dB nominal return loss throughout the 1–22-GHz band of operation, while large-signal measurements show about 19-W peak output power at about 39% power-added efficiency (PAE); excellent results compare favorably versus a wirebonded equivalent and represent a significant improvement over the previous literature.
5 November 2025 in IEEE Transactions on Components, Packaging and Manufacturing Technology
This work presents a novel approach for the design and additive manufacture of high frequency shielded interconnects with enhanced immunity to electromagnetic interference (EMI). Connections between a bare die microwave monolithic integrated circuit (MMIC) and printed circuit board (PCB) are fabricated via the in-situ layered deposition of dielectrics and conductors to realize 2.5D asymmetric striplines. Syringe-dispense and aerosol-jet print (AJP) direct-write (DW) techniques are leveraged for selective and high-resolution printing of well-matched structures. Samples are manufactured using simple passive thru-line bare die MMIC’s which show improved impedance matching and an additional 5GHz of matched bandwidth vs. conventional bondwire interconnects. To demonstrate the EMI shielding enhancement, fabrication is repeated using the same bare die MMIC’s with the thru-lines removed via chemical etching in order to measure the “over-the-top” feedback coupling between ports from 0.010-40GHz. The printed shielded interconnects exhibit a reduction in the feedback coupling of as much as 25dB – or 99.7% – when compared with conventional bondwires, for a total feedback isolation of as much as 80dB. This is an excellent result which enables continued component miniaturization and circuit compaction efforts for next-generation high frequency electronics by reducing crosstalk and feedback between proximate structures.