Oruç Köklükaya

Oruç Köklükaya

Auto-generated profile, based on publicly available information

Oruç Köklükaya

Department of Fiber and Polymer Technology, KTH Royal Institute of Technology, Teknikringen 56, SE-100 44 Stockholm, Sweden

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 August 2017 in ACS Applied Materials & Interfaces
Verified
Journal Article
Closed access
OKOruç Köklükaya
Oruç Köklükaya
Federico CarosioFederico Carosio
Federico Carosio
LWLars Wågberg
Lars Wågberg

19 October 2015 in ACS Applied Materials & Interfaces
Verified
Journal Article
Closed access
OKOruç Köklükaya
Oruç Köklükaya
Federico CarosioFederico Carosio
Federico Carosio
Jaime GrunlanJaime Grunlan
Jaime Grunlan
LWLars Wågberg
Lars Wågberg

1 February 2020 in Carbohydrate Polymers
Verified
Journal Article
Closed access
OKOruç Köklükaya
Oruç Köklükaya
FCFederico Carosio
Federico Carosio
VDVerónica López Durán
Verónica López Durán
LWLars Wågberg
Lars Wågberg

15 March 2018 in Cellulose
Verified
Journal Article
Open access
PDF file
OKOruç Köklükaya
Oruç Köklükaya
FCFederico Carosio
Federico Carosio
LWLars Wågberg
Lars Wågberg
The layer-by-layer (LbL) technology was used to adsorb polyelectrolyte multilayers consisting of cationic polyethylenimine (PEI) and anionic sodium hexametaphosphate (SHMP) onto cellulose fibers in order to enhance the flame-retardancy and tensile strength of paper sheets made from these fibers. The fundamental effect of PEI molecular mass on the build-up of the multilayer film was investigated using model cellulose surfaces and a quartz crystal microbalance technique. The adsorption of a low (LMw) and a high molecular weight (HMw) PEI onto cellulose fibers and carboxymethylated (CM) cellulose fibers was investigated using polyelectrolyte titration. The fibers were consecutively treated with PEI and SHMP to deposit 3.5 bilayers (BL) on the fiber surfaces, and the treated fibers were then used to prepare sheets. In addition, a wet-strength paper sheet was prepared and treated with the same LbL coatings. Thermal gravimetric analysis of LbL-treated fibers showed that the onset temperature for cellulose degradation was lowered and that the amount of residue at 800 °C increased. A horizontal flame test and a vertical flame test were used to evaluate the combustion behavior of the paper sheets. Papers prepared from both cellulose fibers and CM-cellulose fibers treated with HMw-PEI/SHMP LbL-combination self-extinguished in a horizontal configuration despite the rather low amounts of adsorbed polymer which form very thin films (wet thickness of ca. 17 nm). The tensile properties of handsheets showed that 3.5 BL of HMw-PEI and SHMP increased the stress at break by 100% compared to sheets prepared from untreated cellulose fibers.

1 March 2021 in Carbohydrate Polymers
Verified
Journal Article
Open access
OKOruç Köklükaya
Oruç Köklükaya
RKRose-Marie Pernilla Karlsson
Rose-Marie Pernilla Karlsson
FCFederico Carosio
Federico Carosio
LWLars Wågberg
Lars Wågberg
Layer-by-Layer (LbL) assembled nanocoatings are exploited to impart flame-retardant properties to cellulosic substrates. A model cellulose material can make it possible to investigate an optimal bilayer (BL) range for the deposition of coating while elucidating the main flame-retardant action thus allowing for an efficient design of optimized LbL formulations. Model cellulose gel beads were prepared by dissolving cellulose-rich fibers followed by precipitation. The beads were LbL-treated with chitosan (CH) and sodium hexametaphosphate (SHMP). The char forming properties were studied using thermal gravimetric analysis. The coating increased the char yield in nitrogen to up to 29 % and showed a distinct pattern of micro intumescent behavior upon heating. An optimal range of 10-20 BL is observed. The well-defined model cellulose gel beads hence introduce a new scientific route both to clarify the fundamental effects of different film components and to optimize the composition of the films.