Increasing amount of organic dyes in the ecosystem particularly in wastewater has propelled the search for more efficient low-cost bio adsorbents. Different techniques have been used for the treatment of wastewater containing toxic dyes such as: biological degradation, oxidation, adsorption, reverse osmosis, and membrane filtration. Among all these processes mentioned, adsorption with low cost adsorbents has been recognized as one of the cost effective and efficient techniques for treatment of industrial wastewater from organic and inorganic pollutants. Clays as material adsorbents for the removal of various toxic dyes from aqueous solutions as potential alternatives to activated carbons has recently received widespread attention because of the environmental-friendly nature of clay materials. This chapter presents a comprehensive account of the techniques used for the removal of industrial cationic and anionic dyes from water during the last 10 years with special reference to the adsorption by using low cost materials in decontamination processes. Effects of different adsorption parameters on the performance of clays as adsorbents have been also discussed. Various challenges encountered in using clay materials are highlighted and a number of future prospects for the adsorbents are proposed.
The removal of Pb(II) ions from aqueous solution by sorption onto layered double hydroxides (LDHs) is widely documented, yet the reported capacities range from 13 to over 200 mg g−1. The dispersion is usually ascribed to the layer chemistry but cannot be tested because published values come from widely different operating conditions; this work supplies the missing reference member of a single-protocol series. Carbonate-intercalated Mg2Al–CO3 was prepared by coprecipitation at constant pH, characterized by XRD, SEM–EDX, N2 sorption, DSC and pHPZC, and evaluated as a function of dose, pH, contact time, concentration and temperature. Equilibrium was reached within 60 min, the kinetics were pseudo-first-order, the Redlich–Peterson and Langmuir equations fitted the isotherm best with a monolayer capacity of 59.1 mg g−1, and the uptake was spontaneous and endothermic (ΔH° = 11.1 kJ mol−1). They are then compared with two isostructural phases previously published by our team, Mg2[FeAl]–CO3 and Zn2[FeAl]–CO3, prepared and tested under strictly identical conditions; no new experiment was performed on these solids, whose values are quoted here for comparison only. Replacing half of the Al(III) by Fe(III) doubles qm to 118.8 mg g−1 and replacing Mg(II) by Zn(II) raises it to 87.9 mg g−1. Normalized to the BET surface area, however, the three capacities converge on 1.55 ± 0.07 mg m−2: the layer composition acts on Pb(II) uptake only through the accessible surface area it generates, not through the intrinsic reactivity of the surface. Sorbent design should therefore target textural disorder rather than a particular cation pair.
The removal of Pb(II) ions from aqueous solution by sorption onto layered double hydroxides (LDHs) is widely documented, yet the reported capacities range from about 60 to about 120 mg g−1. This dispersion is usually ascribed to the layer chemistry, but this attribution cannot be tested because the published values were obtained under widely different operating conditions; this work supplies the missing reference member of a single-protocol series. Carbonate-intercalated Mg2Al–CO3 was prepared by coprecipitation at constant pH, characterized by XRD, SEM–EDX, N2 sorption, DSC and pHPZC measurement, and evaluated as a function of sorbent dose, pH, contact time, initial concentration and temperature. Equilibrium was reached within 60 min; the kinetics followed the pseudo-first-order model; the Redlich–Peterson and Langmuir equations best fitted the isotherm (monolayer capacity, 59.1 mg g−1); and the uptake was spontaneous and endothermic (ΔH° = 11.1 kJ mol−1). These results were then compared with those previously published by our group for two isostructural phases, Mg2[FeAl]–CO3 and Zn2[FeAl]–CO3, prepared and tested under strictly identical conditions; no new experiments were performed on these solids, whose values are quoted for comparison only. Replacing half of the Al(III) with Fe(III) doubled qm to 118.8 mg g−1, whereas further replacing Mg(II) with Zn(II) lowered it to 87.9 mg g−1. Normalized to the BET surface area, however, the three capacities converge on 1.55 ± 0.07 mg m−2: the layer composition acts on Pb(II) uptake only through the accessible surface area it generates, not through the intrinsic reactivity of the surface. Sorbent design should therefore target textural disorder rather than a particular cation pair.