Benson B. Gathitu

Benson B. Gathitu

Auto-generated profile, based on publicly available information

Benson B. Gathitu

Department of Agricultural and Biosystems Engineering Jomo Kenyatta University of Agriculture and Technology Nairobi Kenya

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
27 October 2023 in Heliyon
Verified
Journal Article
Open access
Lilies Kathami KathumbiLilies Kathami Kathumbi
Lilies Kathami Kathumbi
PHPatrick G. Home
Patrick G. Home
JRJames Raude
James Raude
BGBenson B. Gathitu
Benson B. Gathitu
Biodiesel has several environmental benefits, such as biodegradability, renewability and lower soot emissions. However, biodiesel has undesirable properties such as higher viscosity and density and low calorific value compared to petroleum diesel, resulting in high Brake Specific Fuel Consumption (BSFC), reduced Brake Power (BP) and increased NOX emissions creating an environmental concerns in biodiesel development. This study investigated the effects of synthesizing transesterification catalysts (CaO and NaOH) with Citric Acid (CA) on the quality of biodiesel and biodiesel blends produced from Black Soldier Fly Larvae (BSFL) (Hermetia Illucens). The quality of biodiesel and blends was determined based on fuel properties, engine performance and emission composition characteristics. The tests were performed on a single-cylinder, four-stroke, Compression Ignition (CI) diesel engine at five loads at a constant speed of 1500 rpm. The results showed that synthesizing the catalysts with CA significantly affected the fatty acid profile of the biodiesel compared to physical fuel properties. B100 (pure BSFL biodiesel) exhibited higher BSFC by 10.57–13.97 % and lower BP by 4.21–7.83 % than diesel fuel. However, the Brake Thermal Efficiency (BTE) of biodiesel was higher than that of diesel fuel by 0.82–4.34 % at maximum load. Synthesizing catalysts with CA improved the viscosity of biodiesel by 0.93–2.81 % and effectively reduced NOX, HC and Smoke opacity by 2.23–3.16 %, 4.95–5.83 % and 20.51–41.15 %, respectively.

1 December 2023 in Energy Storage and Saving
Verified
Journal Article
Open access
FNFredrick Irungu Njuguna
Fredrick Irungu Njuguna
HNHiram M. Ndiritu
Hiram M. Ndiritu
BGBenson B. Gathitu
Benson B. Gathitu
MHMeshack Hawi
Meshack Hawi
JMJotham Muthoka Munyalo
Jotham Muthoka Munyalo

30 October 2023 in Journal of Agriculture, Science and Technology
Verified
Journal Article
Open access
PDF file
JOJared O. Ondiba
Jared O. Ondiba
CKChristopher L. Kanali
Christopher L. Kanali
BGBenson B Gathitu
Benson B Gathitu
SOStephen N. Ondimu
Stephen N. Ondimu
Due to increased environmental pollution as a result of high emission rates from agro-processing industries, the effluents must be cleaned up before being released into the environment. This study outlines the use of green algae for nutrient removal from agro-processing effluents discharged from three agro-industries (namely coffee, dairy, and tannery) in Kenya and how they can be used for the propagation of microalgae for biofuel production. Green algae were grown inside a photobioreactor containing the three agro-industrial effluents as nutrient media for 21 days. Thereafter, the algae were harvested and evaluated for biofuel production. The effectiveness of green algae (chlorella ssp) to extract the cations from the various agro-processing effluents was used to gauge how well they performed. Additionally, the algae growth rate, quantity of lipids, and biomass generated were used to evaluate the strains' effectiveness in producing biofuel. The results indicate that the highest maximum algae growth rate of 14.528 mg/mL occurred in the dairy effluent. The corresponding values for the coffee and tannery effluents were 13.016 mg/mL and 10.866 mg/mL, respectively. Biochemical analysis was done to establish the amount of biomass in the algae. The results showed that there was higher biomass productivity per day of 293.944, 124.849, and 91.997 μg/mL for the dairy, coffee, and tannery effluents, respectively. The contents of linolenic acid in the chlorella strain in the dairy, coffee, and tannery effluents were 13.21, 12.86, and 15.98%, respectively. The values obtained were slightly above the recommended lower limit value of 12% (EN 14214, 2004) for the production of quality biofuels. The results further show that high chemical oxygen demand removal (maximum of 47.7–67.8%) and total phosphorus removal (maximum of 95%) were achieved in all three effluents. Finally, the fatty acid methyl ester profiles produced indicated that the lipid content of the cultivated green algae was appropriate for the production of biofuel.

30 October 2023 in Journal of Agriculture, Science and Technology
Verified
Journal Article
Open access
PDF file
COChristopher Ong’era
Christopher Ong’era
BGBenson Gathitu
Benson Gathitu
SMSYLVIA MURUNGA
SYLVIA MURUNGA
PKPatrick Kuloba
Patrick Kuloba
JGJeremiah Gathirwa
Jeremiah Gathirwa
The growing need for energy and the emphasis on reducing emissions have brought attention to the importance of developing renewable energy sources, specifically biofuels. However, using vegetable oils directly in diesel engines is hindered by their high viscosity, low ability to evaporate, and high content of polyunsaturated fats. Nanoemulsions, which are created without traditional surfactants, have demonstrated remarkable thermodynamic stability. This offers a potential solution to the challenges encountered with biofuels. This paper aimed to study the system of rapeseed oil-ethanol and 1-heptanol to understand the effects these nanoemulsions have on the calorific value and flash point. Ternary fuel blends with varying amounts of ethanol, rapeseed oil, and 1-heptanol were studied at constant weight percentages of 20% 1-heptanol and 30% rapeseed oil. The calorific value was determined by using a bomb calorimeter, and the results show that increasing the amount of 1-heptanol and rapeseed oil was able to increase the calorific value of the blend and maintain it close to that of diesel fuel. The flash point was determined using the Pensky Martens Closed Cup Method according to the American Society for Testing and Materials D93 standard (ASTM Standard D93-02a, 2002), and results show that only blends at 20% and 30% 1-heptanol at a constant of 30% rapeseed oil complied with the flash point requirement for diesel. This finding highlights the potential of the tricomponent fuel being used in an internal combustion engine without modification to the engine. The improved calorific value and flash point of the blends could be attributed to the co-solvent behaviour of 1-heptanol on rapeseed oil and ethanol.

1 January 2022 in SSRN Electronic Journal
Verified
Preprint
Open access
PDF file
HVHofni Dionisisus Venomhata Venomhata
Hofni Dionisisus Venomhata Venomhata
POPeter Obara Oketch
Peter Obara Oketch
BGB.B. Gathitu
B.B. Gathitu
PCPaul Chisale
Paul Chisale
A Flash geothermal-solar hybrid cycle is analyzed numerically when it is operated using different workings. The studied working fluids (n-butane, n-pentane, Cyclopentane, Hexamethyldisiloxane, and Toluene) have a low global warming potential and zero ozone depletion potential. These working fluids were investigated to determine the net power output and pump power when heated using low quality geothermal brine from the separator at Olkaria II power plant in Kenya. The brine was heated from a temperature of 158.9 o C to a higher temperature of 400 o C using a parabolic trough solar collector. In addition, analysis was done to determine how Therminol VP1 fluid pressure and flow rate affected the power output of the Organic Rankine Cycle. Furthermore the pressure and mass flow rate of the brine were adjusted to determine how these affected the net power output of the system. In comparison to other working fluids such as n-pentane, Cyclopentane, Hexamethyldisiloxane (MM), and Toluene, nbutane (R600) demonstrated the highest results in net power output for this hybrid system. As a result, it was chosen as the suitable working fluid for this hybrid system. The impact of Therminol VP1 fluid flow rate and pressure on organic working fluid performance revealed that for this system to generate more power, flow rates should be kept low, around 0.2 kg/s, and pressures should be kept slightly below or equal to 11 bar. As compared to Therminol VP1, the brine pressure and flow rate exhibits opposite behavior.

1 January 2022 in The International Journal of Agriculture and Environmental Research
Verified
Journal Article
Open access
JOJared Ombaye Ondiba
Jared Ombaye Ondiba
CKChristopher L. Kanali
Christopher L. Kanali
BGBenson B. Gathitu
Benson B. Gathitu
SOStephen N. Ondimu
Stephen N. Ondimu