6 March 2024 in SPE Journal
Summary: The perforation-acidizing-testing combined technology has become the key technology for increasing the efficiency and speed of ultradeep well completion testing. However, the shock load and the wellbore pressure surge affect the stability and local strength of the lower packer string system during the perforation detonation. The energy generated by the perforation detonation is the fundamental source of the shock load and the wellbore pressure surge. The effect laws and distribution characteristics of the explosion energy of the perforating shaped charge is urgently needed. Therefore, a fluid-structure coupling method based on a structural-arbitrary Lagrangian-Euler algorithm (S-ALE) is used to construct a numerical model to forecast the explosion energy. The feasibility of the numerical model is verified by comparison with the field experimental results. The detailed studies on the output value and distribution characteristics of the explosion energy are carried out. The main control factors and influencing laws of the explosion energy are clarified. Then, an equation for the explosion energy prediction is fitted to lay the foundation for studying the wellbore pressure surge and the lower packer string system failure caused by the perforation detonation. The obtained results indicate that the explosion energy is mainly divided into three parts: the jet kinetic energy, the shell case energy, and the pressure surge energy. The pressure surge energy can reach 59.254 to 66.08%, the jet kinetic energy can reach 9.895 to 17.159%, and the shell case energy can reach 21.426 to 24.325%. The major sensitive parameters that affect the pressure surge energy are ranked as follows: the explosive mass, the explosive type, the shell thickness, the standoff distance, the cone angle of the liner, and the shot density. This work provides a reliable prediction method for the accurate description of the explosion energy conversion, which is critical for improving the success rate of the perforation-acidizing-testing combined technology.
27 June 2023 in SPE Journal
Summary: Among the casing failures in 46 ultradeep wells in a particular block, 11 ultradeep wells had the same casing failure forms occur during the drilling of cement plugs. The casing failure forms are local bending deformation and local internal pressure damage, which eventually led to a local burst failure of the casing in the 11 typical ultradeep wells. Therefore, a casing strength checking model is established to investigate the primary reasons for the local burst failure of the casing and the local burst failure mechanism of the casing. A case study is performed on casing in typical ultradeep wells with force conditions to evaluate the safety state of the casing and make necessary recommendations to improve its safety. The obtained results indicate that an abnormally high dogleg (AHD), a decrease in the temperature at the bottom of the casing, and an annulus trap space are the characteristics of typical ultradeep wells, and the local burst failure of the casing is caused by the coupled superposition impact of a decrease in the annulus pressure buildup (APB), the casing temperature effect, and the magnification effect of the casing bending stress. The safety factor of the casing can be increased by changing the operation parameters and the material properties of the casing. To address the casing failure problems during the drilling of cement plugs in typical ultradeep wells, the protection and monitoring of the seal quality of the cement sheath should be improved to avoid expansion of the well diameter and formation of the annulus trap space. The casing strength and the injection temperature of the drilling fluid can be increased, and the drilling fluid displacement can be decreased.
24 February 2025 in SPE Journal
Summary: To accurately predict the sustained casing pressure resulting from tubing leakage in high-pressure and high-temperature (HPHT) gas wells during production operations, we developed a predictive model that incorporates the effects of tubing leakages, wellbore temperature changes, and multiannulus interactions. First, we determined the thermodynamic parameters of the annular liquid through a combination of experimental and computational methods. Next, we formulated a transient model to predict wellbore temperature and pressure. Then, we analyzed the coupling relationship between tubing leakages, wellbore temperature changes, and multiannulus interactions, and proposed an equation to calculate the sustained casing pressure. Finally, to illustrate the significance of coupled effects of multiple factors, we conducted a comparative case study using both the new model, which incorporates these effects, and the existing model, which considers only the tubing leakage. The characteristics of the sustained casing pressure were analyzed, and a sensitivity analysis was performed. The results show that, compared with measured data, the average error of the new model was 9.2%, which was much lower than the existing model’s 21.6%. The increase rate and maximum value of the annular pressure obtained by the new model were higher than those of the existing model. When the equivalent diameter of the leakage point was less than 0.65 mm, the coupled effects of multiple factors had a more pronounced impact on the sustained casing pressure. Optimizing the annular liquid density proved to be a more economical and effective method for mitigating the sustained casing pressure. This model offers valuable technological support for the prediction and analysis of the sustained casing pressure during production operations.
28 March 2023 in SPE Drilling & Completion
Summary: By creating a reverse deflection, negative-displacement horizontal well technology can successfully address the issue of construction challenges brought on by too little displacement in front of the horizontal well target. However, conventional horizontal well casing string running models are unsuitable for negative-displacement horizontal wells. This is because conventional horizontal well models assume that the casing string is in contact with the lower side of the borehole, which is inconsistent with the actual situation in negative-displacement horizontal wells. In this study, we examine the effects of fluid viscous resistance and internal and external fluid interaction forces on the running of the casing string using the Gaussian method and the complementary surface equivalence method. Based on the bending beam theory, we establish a deflection model to examine the interaction between the casing string and the borehole wall in the bending section. The friction and hookload calculation models of each well section and the strength check models are also established. The calculation results show that, according to the aforementioned model, there is an average error of 7.5% between the measured data and the calculated frictional force of the H1 and H2 negative-displacement horizontal wells. This error is within the reasonable range of field application and attests to the validity of the theoretical model. Finally, we study the influence of running factors on running ability and strength of casing string using the control variable method. The results indicate that the weight of the casing string is positively correlated with the variation law of the running ability of the casing string, the maximum offset distance and the length of the horizontal section are negatively correlated with the running ability of the casing string, and the borehole curvature is positively correlated with the variation law of the connection stress of the internal and external threads of the casing string. Therefore, in the process of running the casing string in negative-displacement horizontal wells, using heavier casing string and reducing the maximum offset distance and horizontal section length can improve the running ability of the casing string.
1 March 2025 in Physics of Fluids
To accurately predict sustained annular pressure (SAP) resulting from tubing integrity failures in ultra-deep gas wells, a new prediction model is developed by considering the effect of leakage states of leakage points and the interaction between volumes of gas leakage and liquid leakage. First, a new calculation equation for the SAP is established by analyzing the coupling relationship of multiple leakage points. Then, a tubing-casing annulus is divided into several segments and transient annular pressure is solved by iteration methods. Finally, the impact of sizes and the number of leakage points are mainly studied. The results show that the maximum error of the new model is only 3.81% by comparison with the measured data. For the case of two leakage points, when the size of the lower leakage point is larger than the upper leakage point, the recovery process has a significant point of the abrupt change with a pressure of 9.15 MPa, and the recovery trend is first rapid (the average recovery rate is 1.83 MPa/h) and then slow (the average recovery rate is 0.40 MPa/h). The number of leakage points only impacts the recovery rate. When the position of leakage point exceeds 3000 m, the impact on the recovery rate becomes relatively marginal. This means that the closer the leakage point is to wellhead, the greater the effect on the recovery rate, so it is necessary to reasonably optimize upper tubing structure to ensure its integrity. These findings lay a theoretical foundation for ensuring the wellbore safety of ultra-deep gas wells.
28 January 2025 in Journal of Pressure Vessel Technology
With increasing wellbore depth, the environmental conditions become progressively more severe, characterized by elevated temperatures and pressures. Consequently, the pressure variations within the well induced by Tubing Conveyed Perforation (TCP) operations exhibit a more pronounced intensity. These nonlinear pressure fluctuations generate significant impact loads at the bottom of the perforating gun, which can cause failure of the perforating tubing. A transient nonlinear pressure field model of perforation explosion was established based on hydraulic-mechanical coupling to effectively control the risk of accidents. The model considers the effects of several hundred perforation charges and their precise placement in relation to blind holes, thus taking into account the impact of shot density. As a result, the model more accurately reflects actual field conditions. The study investigated the evolution of nonlinear pressure fields at different positions of the entire tubing under perforation explosion and analyzed the influence of different factors on nonlinear pressure fluctuations at the bottom of the perforating gun. The results showed that the peak pressure of the perforation section was much higher than that of the tubing section and the rathole section, maintaining at approximately 200 MPa. The pressure wave attenuated to the initial wellbore pressure of about 80 MPa only seven meters away from the perforation section center. The peak pressure at the bottom of the perforating gun was positively correlated with the initial wellbore pressure, perforating fluid density, shot density, and quantity of explosive. When the explosive mass was the same, RDX explosive in RDX, HMX, HNS, and TNT caused the largest peak pressure at the bottom of the perforating gun, with TNT causing the smallest. These results provided guidance for the prediction of TCP wellbore nonlinear pressure fluctuation.