22 January 2021 in Science
Modeling single-atom reactivity: Noble metals often perform best for demanding reactions such as oxygen reduction, an effect often explained by the position of their d-band. One way to minimize the cost of noble metals is to disperse them as single atoms. To model the reactivity of supported single atoms, Hulva et al. evaporated different transition metals such as nickel, silver, and iridium on an Fe 3 O 4 (001) support. Single atoms adsorbed in the same twofold site between underlying rows of surface iron atoms. In studies of CO adsorption as a proxy for reactivity, the d-band was strongly affected by the charge transfer to the support and CO-induced structural changes. These effects can weaken the adsorption energy compared with the expected values based on electronic structure alone. Science , this issue p. 375
24 July 2019 in Angewandte Chemie International Edition
Single‐atom catalysts (SACs) bridge homo‐ and heterogeneous catalysis because the active site is a metal atom coordinated to surface ligands. The local binding environment of the atom should thus strongly influence how reactants adsorb. Now, atomically resolved scanning‐probe microscopy, X‐ray photoelectron spectroscopy, temperature‐programmed desorption, and DFT are used to study how CO binds at different Ir1 sites on a precisely defined Fe3O4(001) support. The two‐ and five‐fold‐coordinated Ir adatoms bind CO more strongly than metallic Ir, and adopt structures consistent with square‐planar IrI and octahedral IrIII complexes, respectively. Ir incorporates into the subsurface already at 450 K, becoming inactive for adsorption. Above 900 K, the Ir adatoms agglomerate to form nanoparticles encapsulated by iron oxide. These results demonstrate the link between SAC systems and coordination complexes, and that incorporation into the support is an important deactivation mechanism.
15 June 2021 in Chemistry of Materials
12 June 2023 in ACS Catalysis
The NiOOH electrode is commonly used in electrochemical alcohol oxidations. Yet understanding the reaction mechanism is far from trivial. In many cases, the difficulty lies in the decoupling of the overlapping influence of chemical and electrochemical factors that not only govern the reaction pathway but also the crystal structure of the in situ formed oxyhydroxide. Here, we use a different approach to understand this system: we start with synthesizing pure forms of the two oxyhydroxides, β-NiOOH and γ-NiOOH. Then, using the oxidative dehydrogenation of three typical alcohols as the model reactions, we examine the reactivity and selectivity of each oxyhydroxide. While solvent has a clear effect on the reaction rate of β-NiOOH, the observed selectivity was found to be unaffected and remained over 95% for the dehydrogenation of both primary and secondary alcohols to aldehydes and ketones, respectively. Yet, high concentration of OH- in aqueous solvent promoted the preferential conversion of benzyl alcohol to benzoic acid. Thus, the formation of carboxylic compounds in the electrochemical oxidation without alkaline electrolyte is more likely to follow the direct electrochemical oxidation pathway. Overoxidation of NiOOH from the β- to γ-phase will affect the selectivity but not the reactivity with a sustained >95% conversion. The mechanistic examinations comprising kinetic isotope effects, Hammett analysis, and spin trapping studies reveal that benzyl alcohol is oxidatively dehydrogenated to benzaldehyde via two consecutive hydrogen atom transfer steps. This work offers the unique oxidative and catalytic properties of NiOOH in alcohol oxidation reactions, shedding light on the mechanistic understanding of the electrochemical alcohol conversion using NiOOH-based electrodes.
5 November 2020 in Chemistry of Materials
24 July 2019 in Angewandte Chemie
Single‐atom catalysts (SACs) bridge homo‐ and heterogeneous catalysis because the active site is a metal atom coordinated to surface ligands. The local binding environment of the atom should thus strongly influence how reactants adsorb. Now, atomically resolved scanning‐probe microscopy, X‐ray photoelectron spectroscopy, temperature‐programmed desorption, and DFT are used to study how CO binds at different Ir1 sites on a precisely defined Fe3O4(001) support. The two‐ and five‐fold‐coordinated Ir adatoms bind CO more strongly than metallic Ir, and adopt structures consistent with square‐planar IrI and octahedral IrIII complexes, respectively. Ir incorporates into the subsurface already at 450 K, becoming inactive for adsorption. Above 900 K, the Ir adatoms agglomerate to form nanoparticles encapsulated by iron oxide. These results demonstrate the link between SAC systems and coordination complexes, and that incorporation into the support is an important deactivation mechanism.