Jae-Yeon Shim

Jae-Yeon Shim

Auto-generated profile, based on publicly available information

Jae-Yeon Shim

Research Center for Electrical and Information Technology, Seoul Nat’l University of Science and Technology, Seoul 01811, South Korea

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 January 2019 in IEEE Transactions on Antennas and Propagation
Verified
Journal Article
Closed access
PDPhilip Ayiku Dzagbletey
Philip Ayiku Dzagbletey
JSJae-Yeon Shim
Jae-Yeon Shim
JCJae-Young Chung
Jae-Young Chung
A dual-polarized Vivaldi antenna pair has been designed for use in a vehicle-to-anything (V2X) measurement facility. The operating bandwidth is from 560 MHz to 7.7 GHz (173% fractional bandwidth), covering all the existing V2X communication frequencies. The ultrawideband (UWB) property was achieved by integrating quarter-wave baluns at the feeding point of two orthogonally crossed Vivaldi antennas. The measured port isolation between the two antennas is better than -28 dB. The cross-polarization discrimination of better than 17.2 dB and antenna gain of up to 9.2 dB have also been realized across the whole bandwidth. Three of the designed antennas were mounted on a vehicle testing facility and were used to measure the radiation patterns of a roof-top shark antenna under four different V2X scenarios. That is, vehicle-to-pedestrian, vehicle-to-vehicle, and vehicle-to-infrastructure and vehicle-to-network. The results have also been presented in this communication.

26 June 2019 in IEEE Sensors Journal
Verified
Journal Article
Closed access
BRBiswarup Rana
Biswarup Rana
JSJae-Yeon Shim
Jae-Yeon Shim
JCJae-Young Chung
Jae-Young Chung
The brain-machine interface (BMI) is a new area of research and it is still in the development stage. The key component for the brain-machine interface is internal and external antennas. In this paper, we propose an implantable antenna for wireless brain signal sensing and monitoring using an inhomogeneous multi-layer model of the human head. A model with seven layers composed of skin, bone, fat, dura, cerebro spinal fluid (CSF), grey matter and white matter was adopted for our multi-layer model. The antenna was embedded below the bone and above the dura of the head phantom. Artificial tissue emulating (ATE) materials were fabricated in semi-solid form and measurement was carried out to check the permittivity and loss tangent of each semi-solid ATE. Implanted antennas for wireless brain signal monitoring data must be compact, lightweight and biocompatible. The proposed antenna was designed with Taconic RF-35 as the substrate with an overall size of 10 mm ×10 mm × 0.5 mm3. The proposed antenna has a -10 dB reflection bandwidth of 2.42-2.50 GHz and a gain of -25 dBi at the broadside direction. The top and bottom insulators with a thickness of 0.5 mm each were also designed with a Taconic RF-35 substrate. A good agreement between simulated and measured results was achieved for the proposed antenna for both in free space and inside of head phantom.

8 January 2019 in IEEE Access
Verified
Journal Article
Open access
JSJae-Yeon Shim
Jae-Yeon Shim
JGJong-Gyu Go
Jong-Gyu Go
JCJae-Young Chung
Jae-Young Chung
A wideband phased array antenna for the use in 5G millimeter-Wave (mmWave) mobile terminal is presented. The proposed array antenna was designed based on the Tightly Coupled Dipole Array (TCDA) technique to achieve a low profile and broadband impedance matching characteristic. Unlike previously reported TCDAs implemented with 2D arrays on a vertical ground plane, the proposed 1D array antenna exhibited the maximum beam direction parallel to the ground which is suitable for mobile terminal applications. Using a full-wave electromagnetic simulation tool, a 1 × 8 TCDA was designed on a multilayer substrate including a reflector surface in the middle to replace a vertical ground plane. Prototypes were fabricated and measured with feeding networks designed for 0o and 30o scanning scenarios. The size of the proposed antenna (excluding the feeding network) was 42.3 × 12.05 × 0.535 mm3. The measured bandwidth that subject to S11 < -10 dB criterion was 22.5 – 32.5 GHz, which covers most of the worldwide 5G mmWave frequency band candidates at the 20 GHz band range.

15 January 2020 in IEEE Sensors Journal
Verified
Journal Article
Closed access
JSJae-Yeon Shim
Jae-Yeon Shim
JCJae-Young Chung
Jae-Young Chung
In this paper, we present a complex permittivity measurement technique for artificial tissue emulating (ATE) materials. Recently, ATE materials have gained increasing attention due to their importance on the in-vitro testing for implantable biomedical devices. They are in semi-solid state and have frequency dependent dielectric properties, thus a broadband characterization technique is called for to measure their permittivity. The target frequency range of the proposed broadband technique is 0.5 – 6 GHz and is based on an open-ended coaxial probe (OECP). Different from the commercial OECP techniques, the in-house built OECP system employs simpler calibration steps which eliminate the need of short-standard measurement often producing errors. The equivalent circuit analysis shows that the short-standard measurement can be substituted by the open-standard measurement with the opposite polarity. The validity of the proposed technique was demonstrated by measuring the complex permittivity of ATE materials for brain in-vitro testing.