14 March 2016 in International Journal of Fracture
Ductile failure of structural metals is relevant to a wide range of engineering scenarios. Computational methods are employed to anticipate the critical conditions of failure, yet they sometimes provide inaccurate and misleading predictions. Challenge scenarios, such as the one presented in the current work, provide an opportunity to assess the blind, quantitative predictive ability of simulation methods against a previously unseen failure problem. Rather than evaluate the predictions of a single simulation approach, the Sandia Fracture Challenge relies on numerous volunteer teams with expertise in computational mechanics to apply a broad range of computational methods, numerical algorithms, and constitutive models to the challenge. This exercise is intended to evaluate the state of health of technologies available for failure prediction. In the first Sandia Fracture Challenge, a wide range of issues were raised in ductile failure modeling, including a lack of consistency in failure models, the importance of shear calibration data, and difficulties in quantifying the uncertainty of prediction [see Boyce et al. (Int J Fract 186:5–68, 2014) for details of these observations]. This second Sandia Fracture Challenge investigated the ductile rupture of a Ti–6Al–4V sheet under both quasi-static and modest-rate dynamic loading (failure in \(\sim \)0.1 s). Like the previous challenge, the sheet had an unusual arrangement of notches and holes that added geometric complexity and fostered a competition between tensile- and shear-dominated failure modes. The teams were asked to predict the fracture path and quantitative far-field failure metrics such as the peak force and displacement to cause crack initiation. Fourteen teams contributed blind predictions, and the experimental outcomes were quantified in three independent test labs. Additional shortcomings were revealed in this second challenge such as inconsistency in the application of appropriate boundary conditions, need for a thermomechanical treatment of the heat generation in the dynamic loading condition, and further difficulties in model calibration based on limited real-world engineering data. As with the prior challenge, this work not only documents the ‘state-of-the-art’ in computational failure prediction of ductile tearing scenarios, but also provides a detailed dataset for non-blind assessment of alternative methods.
1 September 2017 in Journal of Materials Science & Technology
The final publication is available at Elsevier via http://dx.doi.org/10.1016/j.jmst.2017.04.004 © 2017. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/Uniaxial tension and compression tests were conducted to investigate the quasi-static performance of ZK60 Mg alloy in cast, followed by forging at optimum temperature of 450°C and a ram speed of 39mmmin-1. Microstructure and texture analysis showed that the as-cast alloy exhibited a dendritic structure with casting porosity and random texture. In contrast, the forged alloy exhibited a refined grain structure with a significant reduction in casting porosity, while the texture changed to sharp basal texture. Measured mechanical properties of the forged alloy showed that strength did not change, however, ductility improved by 75%. The analysis of the fracture surface of the forged alloy under tension revealed a ductile fracture with dimple morphology, while the as-cast alloy displayed a brittle fracture with open pores. This demonstrated that the reduction of casting defects and dendritic morphology, as well as the evolution of recrystallized grains, enhanced ductility, while partial dynamic recrystallization through the forging process resulted in only marginal modification of strength in the forged condition
1 April 2017 in Journal of Alloys and Compounds
1 October 2017 in Materials Science and Engineering: A
The final publication is available at Elsevier via https://doi.org/10.1016/j.msea.2017.08.086 © 2017. This manuscript version is made available under the CC-BY-NC-ND 4.0 licenseThe effect of forging on the low cycle fatigue (LCF) behavior of cast AZ31B was investigated. The forging process was conducted at a temperature of 450°C and speed of 390mm/min. Fully reversed (Rε=-1) strain controlled cyclic tests were performed on as-cast and forged materials under total strain amplitudes of 0.1%-1.2%. Forging eliminated the dendritic morphology and reduced β-phase intermetallics observed in the cast alloy. Additionally sharp basal texture and bimodal grain structure were developed. Generally, the forged material was found to exhibit longer fatigue life, especially at lower strain amplitudes. This was attributed to the grain refinement and the developed basal texture that changed the alloy’s deformation behavior. Also, the forged material achieved significantly higher stresses at the same total strain amplitudes compared to cast AZ31B, and substantial cyclic hardening occurred during cyclic loading. At the same time, considerable tension-compression asymmetry was observed in the forged AZ31B during LCF testing. The Smith-Watson-Topper model and Jahed-Varvani energy model were employed and both models were found to accurately predict the experimentally obtained fatigue life of both alloy conditions. The Jahed-Varvani model accurately predicted fatigue life within a factor of 1.5 especially for the asymmetric behavior of forged AZ31B.Natural Sciences and Engineering Research Council of Canada (NSERC) Automotive Partnership Canada (APC) || APCPJ 459269–13 grant Multimatic Technical Centre Ford Motor Company Centerline Windso
1 November 2017 in International Journal of Fatigue
The final publication is available at Elsevier via https://doi.org/10.1016/j.ijfatigue.2017.06.038 © 2017. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/Tensile and strain-controlled fatigue tests were performed to investigate the influence of forging on the performance of cast AZ80 magnesium alloy. The obtained microstructural analysis showed that the as-cast AZ80 magnesium alloy has dendritic α-Mg phase with eutectic Mg17Al12 morphology and a random texture. In contrast, the forged samples showed refined grains and a strong basal texture. During tensile testing, a maximum yield and ultimate tensile strength of 182 MPa and 312 MPa were obtained for the forged samples, representing increases of 121% and 33%, respectively, from the as-cast condition. At the same time, a significant improvement (73%) in ductility was obtained in forged samples. It was also observed that the forged samples achieved comparatively longer fatigue life under strain-controlled cyclic loading. Analysis of the fracture surfaces showed that a cleavage-type morphology was typical for the as-cast samples, while the occurrence of dimples and other evidence of plastic deformation were identified in the fracture surfaces of the forged specimens, indicating a more ductile response. Forging caused grain refinement and texture modification, both of which enhance alloy performance by improving strength and ductility, and leading to longer fatigue life. Strain and energy-based models were investigated for their suitability to predict the life of the forged material. Both the Smith-Watson Topper and the Jahed-Varvani energy-based models gave reliable life prediction.Natural Sciences and Engineering Research Council of Canada (NSERC) through the Automotive Partnership Canada (APC) under APCPJ 459269–13 grant with contributions from Multimatic Technical Centre, Ford Motor Company, and Centerline Windsor are acknowledged
1 May 2006 in International Journal of Impact Engineering