4 May 2023 in Nature Energy
Silicon heterojunction (SHJ) solar cells have reached high power conversion efficiency owing to their effective passivating contact structures. Improvements in the optoelectronic properties of these contacts can enable higher device efficiency, thus further consolidating the commercial potential of SHJ technology. Here we increase the efficiency of back junction SHJ solar cells with improved back contacts consisting of p-type doped nanocrystalline silicon and a transparent conductive oxide with a low sheet resistance. The electrical properties of the hole-selective contact are analysed and compared with a p-type doped amorphous silicon contact. We demonstrate improvement in the charge carrier transport and a low contact resistivity (<5 mΩ cm2). Eventually, we report a series of certified power conversion efficiencies of up to 26.81% and fill factors up to 86.59% on industry-grade silicon wafers (274 cm2, M6 size).
16 October 2024 in Nature Communications
Crystalline-silicon heterojunction back contact solar cells represent the forefront of photovoltaic technology, but encounter significant challenges in managing charge carrier recombination and transport to achieve high efficiency. In this study, we produced highly efficient heterojunction back contact solar cells with a certified efficiency of 27.09% using a laser patterning technique. Our findings indicate that recombination losses primarily arise from the hole-selective contact region and polarity boundaries. We propose solutions to these issues and establish a clear relationship between contact resistivity, series resistance, and the design of the rear-side pattern. Furthermore, we demonstrate that the wafer edge becomes the main channel for current density loss caused by carrier recombination once electrical shading around the electron-selective contact region is mitigated. With the advanced nanocrystalline passivating contact, wafer edge passivation technologies and meticulous optimization of front anti-reflection coating and rear reflector, achieving efficiencies as high as 27.7% is feasible.
12 November 2025 in Nature
15 June 2022 in Advanced Science
Combining electron‐ and hole‐selective materials in one crystalline silicon (Si) solar cell, thereby avoiding any dopants, is not considered for application to photovoltaic industry until only comparable efficiency and stable performance are achievable. Here, it is demonstrated how a conventionally unstable electron‐selective contact (ESC) is optimized with huge boost in stability as well as improved electron transport. With the introduction of a Ti thin film between a‐Si:H(i)/LiF and Al electrode, high‐level passivation (Seff = 4.6 cm s–1) from a‐Si:H(i) and preferential band alignment (ρC = 7.9 mΩ cm2) from low work function stack of LiF/Ti/Al are both stably retained in the newly constructed n‐Si/a‐Si:H(i)/LiF/Ti/Al ESC. A detailed interfacial elements analysis reveals that the efficiently blocked inward diffusion of Al from electrode by the Ti protecting layer balances transport and recombination losses in general. This excellent electron‐selective properties in combination with large process tolerance that enable remarkable device performance, particularly high efficiencies of 22.12% and 23.61%, respectively, are successfully approached by heterojunction solar cells with dopant‐free ESC and dopant‐free contacts for both polarities.
7 May 2024 in Nature Communications
Crystalline silicon solar cells with regular rigidity characteristics dominate the photovoltaic market, while lightweight and flexible thin crystalline silicon solar cells with significant market potential have not yet been widely developed. This is mainly caused by the brittleness of silicon wafers and the lack of a solution that can well address the high breakage rate during thin solar cells fabrication. Here, we present a thin silicon with reinforced ring (TSRR) structure, which is successfully used to prepare free-standing 4.7-μm 4-inch silicon wafers. Experiments and simulations of mechanical properties for both TSRR and conventional thin silicon structures confirm the supporting role of reinforced ring, which can share stress throughout the solar cell preparation and thus suppressing breakage rate. Furthermore, with the help of TSRR structure, an efficiency of 20.33% (certified 20.05%) is achieved on 28-μm silicon solar cell with a breakage rate of ~0%. Combining the simulations of optoelectrical properties for TSRR solar cell, the results indicate high efficiency can be realized by TSRR structure with a suitable width of the ring. Finally, we prepare 50 ~ 60-μm textured 182 × 182 mm2TSRR wafers and perform key manufacturing processes, confirming the industrial compatibility of the TSRR method.
2 March 2021 in Solar RRL