Junjie Wang

Junjie Wang

Auto-generated profile, based on publicly available information

Junjie Wang

State Key Laboratory of Advanced, Special Steels (Shanghai University), School of Materials Science and Engineering, Shanghai University, Shanghai, P. R. China

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 September 2015 in Materials Characterization
Verified
Journal Article
Closed access
UDUyime Donatus
Uyime Donatus
GTG.E. Thompson
G.E. Thompson
XZXiaorong Zhou
Xiaorong Zhou
JWJ. Wang
J. Wang
ACA. Cassell
A. Cassell
KBK. Beamish
K. Beamish

1 September 2017 in Corrosion Science
Verified
Journal Article
Open access
BLBing Liu
Bing Liu
XZXinxin Zhang
Xinxin Zhang
XZXiaorong Zhou
Xiaorong Zhou
THTeruo Hashimoto
Teruo Hashimoto
JWJunjie Wang
Junjie Wang

1 October 2015 in Materials & Design
Verified
Journal Article
Closed access
UDUyime Donatus
Uyime Donatus
GTG.E. Thompson
G.E. Thompson
XZXiaorong Zhou
Xiaorong Zhou
JWJ. Wang
J. Wang
KBK. Beamish
K. Beamish

9 February 2023 in Journal of Materials Processing Technology
Verified
Journal Article
Closed access
FSFengzhen Sun
Fengzhen Sun
PPPavel Penchev
Pavel Penchev
CPCatalin I. Pruncu
Catalin I. Pruncu
JWJunjie Wang
Junjie Wang
CPChris Pargeter
Chris Pargeter
BBBamber R.K. Blackman
Bamber R.K. Blackman

1 January 2015 in Materials Characterization
Verified
Journal Article
Open access
JWJ. Wang
J. Wang
XZXiaorong Zhou
Xiaorong Zhou
GTG.E. Thompson
G.E. Thompson
JHJ.A. Hunter
J.A. Hunter
YYY. Yuan
Y. Yuan
A near-surface layer existed on a cold rolled and annealed foil stock AlFeSi alloy due to severe shear strain during twin-roll casting and subsequent cold rolling. The near-surface layer, with a thickness up to ~ 700 nm and consisting of ultrafine grains with diameters up to 100 nm and high population of voids/microcracks, was present as randomly distributed patches on the alloy surface. The grain boundaries within the near-surface layer were decorated by oxide particles and inclusions of lubricant residue, which reduce the ductility of the near-surface layer. During sheet forming, further shear deformation occurred in the near-surface region due to the friction caused by the sliding contact between the alloy sheet and the forming tool. The differences in the microstructure and the ductility between the near-surface layer and the underlying bulk alloy resulted in cracking within the near-surface layer and/or at the near-surface layer/bulk alloy interface, finally leading to the delamination of patches of the near-surface layer. The delamination generated flake-like alloy debris may significantly modify the property of forming lubricant and influence the tendency to galling during sheet forming.

24 April 2014 in Journal of the Electrochemical Society
Verified
Journal Article
Open access
PDF file
YMY. Ma
Y. Ma
XZXiaorong Zhou
Xiaorong Zhou
JWJ. Wang
J. Wang
GTG. E. Thompson
G. E. Thompson
WHW. Huang
W. Huang
ACA. Crispin
A. Crispin
The effect of the anodizing process parameters and the influence of β′(Mg2Si) phase on the appearance of the anodized AA6063 aluminum alloy have been investigated. It was found that β′(Mg2Si) phase was preferentially oxidized at low anodizing voltages and the selective oxidation of β′(Mg2Si) phase resulted in the development of a rough alloy/film interface and the incorporation of silicon into the porous anodic film, which led to the discoloration of the anodized alloy.