12 October 2020 in IET Electric Power Applications
Hybrid axial field flux‐switching permanent magnet (HAFFSPM) machine exhibits a high‐cogging torque due to its doubly salient structure and flux focusing effect. In consideration of the armature and field windings are both equipped in the HAFFSPM machine, a cogging torque reduction method by the harmonic field current injection is proposed in this study. Initially, the mathematical model of the HAFFSPM machine is analysed. Moreover, the theoretical principle of the proposed method is investigated based on the analytical model of the machine. The amplitude and phase angle of the injected current are calculated according to the harmonic component of the cogging torque. The feasibility of the proposed method is analysed and validated by both the finite‐element analysis method and experiments on the prototype. Finally, the comparison between the proposed method and several topology optimisation methods of the HAFFSPM machine is given to indicate the priority of the harmonic field current injection method on cogging torque reduction.
15 October 2024 in IEEE Journal of Emerging and Selected Topics in Power Electronics
This paper proposes a novel position identification algorithm for permanent magnet synchronous motors (PMSMs) operating at zero and low speed. Traditional high-frequency signal injection methods struggle with phase lag and poor interference rejection, limiting their effectiveness in steady and dynamic conditions. To overcome these challenges, an improved nonlinear tracking differentiator method for precise and rapid estimation of motor position and speed is presented. The proposed method reduces tracking delay by 35% and improves noise immunity by 30% compared to traditional methods. Advanced mathematical analysis and frequency sweep tests validate its effectiveness. Simulation and experimental results confirm enhanced performance in both steady and dynamic states, with the method effectively suppressing 6 th -order harmonic interference from inverter nonlinearity, achieving an attenuation of -43 dB/decade.
12 August 2024 in IEEE Transactions on Applied Superconductivity
In this paper, a novel axial field flux switching permanent magnet machine (AFFSPMM) with modular spoke-type rotor is proposed and optimized for torque performance enhancement. The topology and initial design specifics are introduced in first. Then design variables are categorized by sensitivity analysis method and the machine is optimized by a dual-level comprehensive optimization method, in which response surface model and single variable optimization are adopted for each level to enhance the optimization efficiency. The comparison of electromagnetic performance between initial and optimal machines is carried out in addition. Finally, a prototype machine is manufactured and tested. The experimental results indicate that the desirable torque performance of the machine can be obtained by the proposed optimization method.
1 January 2025 in IET Electric Power Applications
Due to the remarkable performance, dual three‐phase axial flux 33permanent magnet synchronous motors (DTP‐AFPMSMs) are increasingly being adopted in the field of electric vehicles (EVs). However, the installation of position sensors limits the application scenarios of DTP‐AFPMSMs owing to increased complexity, size and cost. This article proposes an innovative high‐speed sensorless control method for surface‐mounted DTP‐AFPMSMs using an improved rotor flux observer. The proposed observer achieves precise rotor flux estimation by filtering out harmonic distortion and noise from the rotor flux of the first winding set using high‐pass and low‐pass filters, followed by a tracking‐mode PI controller that accurately tracks the phase and amplitude of the rotor flux in the second winding set. Therefore, the proposed method can enable accurate rotor position estimation without the need for a phase‐locked loop (PLL) and realise a more precise sensorless motor control. A series of simulations and experiments are carried out to validate the effectiveness of the observer, which reveals that the proposed method can effectively estimate the electrical position angle with a tiny error and presents a considerable improvement over the conventional method.
23 April 2025 in IEEE Transactions on Energy Conversion
In this paper, an axial-field flux-modulated (AFFM) machine with multiple permanent-magnet (PM) excitations for electric vehicle applications is investigated. This study addresses the torque limitation of axial-field rotor-PM machines by investigating the strategic placement of stator PMs with specific magnetization directions, rather than solely relying on increased rotor PM quantity which becomes ineffective beyond certain thresholds. Then, taking axial-field magnetic gears with a gear ratio of 19/5 as the foundation, the evolution processes into corresponding stator-PM and rotor-PM axial-field motors are explored. The physical structures and necessary magnetic coupling conditions of these two topologies are discussed in detail to enhance the performance of the proposed topology. Then machine characteristics, including the flux linkage, back-EMF, torque capability, self-and mutual-inductance, power factor and cogging torque are researched, wherein the torque output of the proposed one is comparable to the sum of stator-PM and rotorPM motors. The effects of specific parameters influenced by the assembly process are also investigated. To demonstrate the competitiveness, the proposed machine was compared against four regular AFFMPM topologies, achieving advancements in torque and PM utilization aspects. Finally, a prototype is manufactured and tested, verifying the FE predictions.
28 August 2024 in IEEE Transactions on Applied Superconductivity
This paper investigates the distribution patterns and influencing factors of AC losses in the flat-wire windings of an axial-flux permanent magnet machine (AFPMM) with dual rotor and segmented stators (DRSS). Firstly, several two- and three-dimensional computational models considering eddy current effects are established to balance accuracy and speed. The dimensions of the stator core, including parameters such as slot openings, slot widths, and slot heights, are analyzed and optimized employing the optimal model. Then, the effects of conductor arrangement, wire gauge, stranding, and frequency on AC losses are studied by applying the three proposed configurations for flat-wire windings. A comparison of eddy current distribution and AC losses per turn is presented. Finally, methods for suppressing AC losses in the flat-wire winding of the AFPMM-DRSS are discussed.