1 June 2020 in Journal of the Energy Institute
1 November 2016 in IOP Conference Series: Materials Science and Engineering
The present work encompasses the impact of temperature (450, 500, 550, 600 °C) on the properties of pyrolysis oil and on other product yield for the co-pyrolysis of Polypropylene (PP) plastics and rice straw. Co-pyrolysis of PP plastic and rice straw were conducted in a fixed-bed drop type pyrolyzer under an inert condition to attain maximum oil yield. Physically, the pyrolysis oil is dark-brown in colour with free flowing and has a strong acrid smell. Copyrolysis between these typically obtained in maximum pyrolysis oil yields up to 69% by ratio 1:1 at a maximum temperature of 550 °C. From the maximum yield of pyrolysis oil, characterization of pyrolysis product and effect of biomass type of the composition were evaluated. Pyrolysis oil contains a high water content of 66.137 wt.%. Furfural, 2- methylnaphthalene, tetrahydrofuran (THF), toluene and acetaldehyde were the major organic compounds found in pyrolysis oil of rice straw mixed with PP. Bio-char collected from co-pyrolysis of rice straw mixed with PP plastic has high calorific value of 21.190 kJ/g and also carbon content with 59.02 wt.% and could contribute to high heating value. The non-condensable gases consist of hydrogen, carbon monoxide, and methane as the major gas components.
29 October 2017 in Journal of Physics: Conference Series
In this work, co-pyrolysis of rice straw and polyethylene terephthalate (PET) was carried out at different temperatures (450,500,550, and 600°C) at ratio 1:1 by using fixed bed drop-type pyrolyzer. The purpose of this work is to determine the effect of pyrolysis temperature on the product yield. As the temperature increased, the pyrolysis oil increased until it reaches certain high temperature (600°C), the pyrolysis oil decreased as of more NCG were produced. The temperature 550°C is considered as the optimum pyrolysis temperature since it produced the highest amount of pyrolysis oil with 36 wt.%. In pyrolysis oil, the calorific value (13.98kJ/g) was low because of the presence of high water content (52.46 wt.%). Main chemicals group from pyrolysis oil were an aldehyde, ketones, acids, aromatics, and phenol and all compound have abundant of hydrogen and carbon were identified. Co-pyrolysis of rice straw and PET produced a higher amount of carbon oxides and recycling back the NCG could increase liquid and char yields.
5 April 2023 in Journal of Advanced Research in Applied Sciences and Engineering Technology
This study aims to find the best material for the manifold and improve airflow in the UniMAP Automotive Racing Team (uniART) exhaust manifold. The exhaust manifold is a part of the exhaust system that collects and delivers exhaust gases from the cylinder head to the exhaust outlet. The exhaust manifold’s design is significant to the engine performance. The current design and new designs of the exhaust manifold were modelled using SOLIDWORKS software. Stainless steel, cast iron and mild steel were chosen as materials for manifold and were studied by conducting the Steady-State Thermal analysis. The flow of the air in the manifold is analysed and evaluated in terms of pressure and velocity. The fluid flow and thermal analysis are simulated in Computational Fluid Dynamics analysis software known as ANSYS. Results of thermal analysis prove that Stainless steel is better than other materials since it has a high temperature difference and low heat flux. The results of fluid flow analysis were compared between the current design and new designs of the exhaust manifold. The outcome indicated that validated Design 2 has a higher velocity value at the outlet and lower pressure at inlets which improves the airflow in the exhaust manifold.
1 May 2020 in IOP Conference Series: Materials Science and Engineering
Plastic waste management has been a problem as most of the plastics are not biodegradable. Although plastics are recyclable, only 21% of total plastic wastes are recycled. Using plastics as gasification feedstock/co-feedstock and converting it to usable energy is one of the solutions of removing plastics waste. Co-gasifying polystyrene (PS) with palm kernel shell (PKS) is promising as both of the feedstocks are abundant and have high energy content. However, the performance of air gasification of PKS and PS has not been studied previously. In this work, co-gasification of PKS and PS was carried out, focusing on the effect of PS content in the feedstock. The PS content was varied from 0 to 30 wt%. By increasing the PS content, the CH4 volume percentage increases, while CO and H2 volume percentage decreases. The high heating value of the producer gas increases with PS content, from 11.95 MJ/Nm3 at 10 wt% PS, to 12.36 MJ/Nm3 at 30 wt% PS. Higher PS content also increases the gas yield percentage.
1 October 2021 in Journal of Physics: Conference Series
When a racing car moves at high velocity, aerodynamic factors will cause a lift and drag force, causing the speeding vehicle to lose stability, traction and speed. To solve this problem, racing cars use a rear spoiler as a medium to reduce drag and lift, increasing the car’s stability. This study explores the idea that focuses on the impact of the angle of attack on UniART SAE race car performance and the effect of angle of attack on drag force and downforce. ANSYS Fluent is used to generate the simulation In the context of the lift force analysis, angle of attack equal to 12.5° produce the most outstanding results and generated the highest negative lift force value between three tested angles. The highest negative lift force generated is 35.658 N at the inlet velocity of 105 km/h. Furthermore, by referring to drag force analysis, it shows an increasing trend when the variable angle of attack parameter is changed to a higher value. Angle 25° produced the highest drag force data which is 60N and the inlet velocity condition is set equal to 105 km/h.