A. S. Davtian

A. S. Davtian

Auto-generated profile, based on publicly available information

A. S. Davtian

“Lasers and Optical Systems” Co., Ltd., St. Petersburg, Russia

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 September 2018 in Optics Letters
Verified
Journal Article
Closed access
PDF file
AKA. F. Kornev
A. F. Kornev
RBR. V. Balmashnov
R. V. Balmashnov
IKI. G. Kuchma
I. G. Kuchma
ADA. S. Davtian
A. S. Davtian
DOD. O. Oborotov
D. O. Oborotov
We demonstrate a diode-pumped master oscillator power amplifier Nd:YAG 1064 nm laser with sub-joule-level output energy of 0.43 J, high pulse repetition rate of 200 Hz, and short pulse duration of 100 ps. The 5 mJ master oscillator consisted of a 100 nJ/100 ps Nd:YVO4 microchip laser and end-pumped Nd:YAG regenerative amplifier. The two-pass output amplifier was based on two ∅10×140  mm Nd:YAG laser rods. We apply an adaptive compensator with an analyzer based on an astigmatic optical system and a quadrant photodiode to compensate for low-order wave-front non-stationary thermal distortions in a high-energy laser amplifier. The adaptive compensator demonstrates high sensitivity to curvature changes of λ/100, and it provides output beam divergence near 1.5×DL in 100 ps 0.43  J×200  Hz of operation mode.

1 September 2019 in Fusion Engineering and Design
Verified
Journal Article
Closed access
AKA.F. Kornev
A.F. Kornev
ADA.S. Davtian
A.S. Davtian
AKA.S. Kovyarov
A.S. Kovyarov
AMA.M. Makarov
A.M. Makarov
DOD.O. Oborotov
D.O. Oborotov
MWM. Walsh
M. Walsh

1 June 2014
Verified
Conference Paper
Closed access
ADA.S. Davtian
A.S. Davtian
ZGZ. V. Gorelova
Z. V. Gorelova
VPV.P. Pokrovskyi
V.P. Pokrovskyi
SSS.S. Sobolev
S.S. Sobolev
STS.S. Terekhov
S.S. Terekhov
End pumped Nd:YAG ring laser with electro-optical Q-switcher was built. Pumping of each laser rod is provided by 45 Watt laser diode module coupled in high-brightness fiber. Single-frequency and unidirectional performance of laser is provided with injection seeding. End overheating of active rod was reduced by using low-concentration active medium. Thermo-optic distortions were compensated.

1 June 2018
Verified
Conference Paper
Closed access
ADA. S. Davtian
A. S. Davtian
AKA. F. Kornev
A. F. Kornev
VKV. V. Koval
V. V. Koval
We developed an approach that ensures high shape stability of intense Nd:YAG laser pulses, based on a "microchip laser - regenerative amplifier" scheme. High-quality laser beam (M 2 <;1.4) at 532 nm with 100-ps 2.5 mJ (RMS<;1%) pulses was obtained at the repetition rates up to 1000 Hz. The reported architecture is flexible enough to design lasers that meet different requirements.

1 June 2018
Verified
Conference Paper
Closed access
RBR. V. Balmashnov
R. V. Balmashnov
ADA. S. Davtian
A. S. Davtian
YKY. V. Katsev
Y. V. Katsev
AKA. F. Kornev
A. F. Kornev
IKI. G. Kuchma
I. G. Kuchma
DOD. O. Oborotov
D. O. Oborotov
We developed 106 W (0.53J × 200 Hz) diode-pumped 1064 nm Nd:YAG laser with pulse duration of ps. 6-pass laser amplifier was based on a single Ø15×140 mm rod. The output beam was flat-top, the beam divergence was 1.5 times the different limit. The SHG efficiency up to 54% was achieved in 17×17×7 mm 3 LBO crystal.

1 October 2018
Verified
Conference Paper
Closed access
DPDenis Prokuratov
Denis Prokuratov
ADArsen Davtian
Arsen Davtian
DPDmitrii Pankin
Dmitrii Pankin
AMAlexandra Mikhaylova
Alexandra Mikhaylova
APAnastasia Povolotckaia
Anastasia Povolotckaia
ASAlexandr Shimko
Alexandr Shimko
The investigation of possibility of using lasers with different wavelength and pulse duration to clean the surface of lead and zinc exterior sculptures was held in this work. Comparison of lasers with different durations was done, pcs laser shown the best results in cleaning both of zinc and lead. The measuring of reflectance of corrosion layers indicates minimum in UV part of spectrum, however there were no positive cleaning results using 355nm 25 ns laser. The pulse duration is much more important parameter in preservation of surface during laser cleaning, as shown. Also, the surface state plays significant role - the technology of producing of object and its history of exposition.