Bo Cui

Bo Cui

Auto-generated profile, based on publicly available information

Bo Cui

Department of Electrical and Computer Engineering, Waterloo Institute for Nanotechnology, University of Waterloo, Waterloo, ON, Canada

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
26 August 2019 in Microsystems & Nanoengineering
Verified
Journal Article
Open access
PDF file
YLYan Li
Yan Li
HZHang Zhang
Hang Zhang
RYRuifeng Yang
Ruifeng Yang
YLYohan Laffitte
Yohan Laffitte
USUlises Schmill
Ulises Schmill
BCBo Cui
Bo Cui
Microneedle technologies have the potential for expanding the capabilities of wearable health monitoring from physiology to biochemistry. This paper presents the fabrication of silicon hollow microneedles by a deep-reactive ion etching (DRIE) process, with the aim of exploring the feasibility of microneedle-based in-vivo monitoring of biomarkers in skin fluid. Such devices shall have the ability to allow the sensing elements to be integrated either within the needle borehole or on the backside of the device, relying on capillary filling of the borehole with dermal interstitial fluid (ISF) for transporting clinically relevant biomarkers to the sensor sites. The modified DRIE process was utilized for the anisotropic etching of circular holes with diameters as small as 30 μm to a depth of >300 μm by enhancing ion bombardment to efficiently remove the fluorocarbon passivation polymer. Afterward, isotropic wet and/or dry etching was utilized to sharpen the needle due to faster etching at the pillar top, achieving tip radii as small as 5 μm. Such sharp microneedles have been demonstrated to be sufficiently robust to penetrate porcine skin without needing any aids such as an impact-insertion applicator, with the needles remaining mechanically intact after repetitive penetrations. The capillary filling of DRIE-etched through-wafer holes with water has also been demonstrated, showing the feasibility of use to transport the analyte to the target sites.

23 December 2014 in Plasmonics
Verified
Journal Article
Closed access
PDF file
JZJian Zhang
Jian Zhang
MIMehrdad Irannejad
Mehrdad Irannejad
BCBo Cui
Bo Cui

12 July 2011 in Discover Nano
Verified
Journal Article
Open access
PDF file
SMSiqi Ma
Siqi Ma
CCCelal Con
Celal Con
Mustafa YavuzMustafa Yavuz
Mustafa Yavuz
BCBo Cui
Bo Cui
We studied the exposure behavior of low molecular weight polystyrene as a negative tone electron beam lithography (EBL) resist, with the goal of finding the ultimate achievable resolution. It demonstrated fairly well-defined patterning of a 20-nm period line array and a 15-nm period dot array, which are the densest patterns ever achieved using organic EBL resists. Such dense patterns can be achieved both at 20 and 5 keV beam energies using different developers. In addition to its ultra-high resolution capability, polystyrene is a simple and low-cost resist with easy process control and practically unlimited shelf life. It is also considerably more resistant to dry etching than PMMA. With a low sensitivity, it would find applications where negative resist is desired and throughput is not a major concern.

4 April 2013 in Discover Nano
Verified
Journal Article
Open access
PDF file
RLRuiyuan Liu
Ruiyuan Liu
FZFute Zhang
Fute Zhang
CCCelal Con
Celal Con
BCBo Cui
Bo Cui
Baoquan SunBaoquan Sun
Baoquan Sun
We demonstrated a novel, simple, and low-cost method to fabricate silicon nanowire (SiNW) arrays and silicon nanohole (SiNH) arrays based on thin silver (Ag) film dewetting process combined with metal-assisted chemical etching. Ag mesh with holes and semispherical Ag nanoparticles can be prepared by simple thermal annealing of Ag thin film on a silicon substrate. Both the diameter and the distribution of mesh holes as well as the nanoparticles can be manipulated by the film thickness and the annealing temperature. The silicon underneath Ag coverage was etched off with the catalysis of metal in an aqueous solution containing HF and an oxidant, which form silicon nanostructures (either SiNW or SiNH arrays). The morphologies of the corresponding etched SiNW and SiNH arrays matched well with that of Ag holes and nanoparticles. This novel method allows lithography-free fabrication of the SiNW and SiNH arrays with control of the size and distribution.

23 September 2013 in Discover Nano
Verified
Journal Article
Open access
PDF file
CCCelal Con
Celal Con
BCBo Cui
Bo Cui
Polydimethylsiloxane (PDMS) is the most popular and versatile material for soft lithography due to its flexibility and easy fabrication by molding process. However, for nanoscale patterns, it is challenging to fill uncured PDMS into the holes or trenches on the master mold that is coated with a silane anti-adhesion layer needed for clean demolding. PDMS filling was previously found to be facilitated by diluting it with toluene or hexane, which was attributed to the great reduction of viscosity for diluted PDMS. Here, we suggest that the reason behind the improved filling for diluted PDMS is that the diluent solvent increases in situ the surface energy of the silane-treated mold and thus the wetting of PDMS to the mold surface. We treated the master mold surface (that was already coated with a silane anti-adhesion monolayer) with toluene or hexane, and found that the filling by undiluted PMDS into the nanoscale holes on the master mold was improved despite the high viscosity of the undiluted PDMS. A simple estimation based on capillary filing into a channel also gives a filling time on the millisecond scale, which implies that the viscosity of PMDS should not be the limiting factor. We achieved a hole filling down to sub-200-nm diameter that is smaller than those of the previous studies using regular Sylgard PDMS (not hard PDMS, Dow Corning Corporation, Midland, MI, USA). However, we are not able to explain using a simple argument based on wetting property why smaller, e.g., sub-100-nm holes, cannot be filled, for which we suggested a few possible factors for its explanation.

1 January 2020 in Journal of Vacuum Science & Technology B
Verified
Journal Article
Closed access
PDF file
RDRipon Kumar Dey
Ripon Kumar Dey
HEHuseyin Ekinci
Huseyin Ekinci
BCBo Cui
Bo Cui
High aspect ratio silicon structures have gained significant interest due to their vast applications. Minimal lateral etch under the mask is essential to achieve such high aspect ratio structures. Previously, the authors reported that chromium oxide is better than metallic chromium as a hard mask for silicon etching in terms of etch rate and selectivity to resist during mask structure fabrication. Here, it is reported that a metal oxide etch mask also gives less lateral etch than a metal etch mask. Following mask structure fabrication by electron beam lithography and lift-off, silicon was etched using a nonswitching (i.e., SF6 and C4F8 gases simultaneously injected into a chamber) pseudo-Bosch process. The amount of lateral etching right underneath the mask is less (roughly half) for Cr2O3 and Al2O3 masks than Cr or Al masks. One plausible explanation for the difference is the metal-assisted plasma etching effect where the metal catalyzes the chemical reaction by injecting holes into the silicon in contact. It is also reported that a higher bias power leads to less undercut than a lower one, due to increased and more directional physical bombardment by ions.