Irina P. Smirnova

Irina P. Smirnova

Auto-generated profile, based on publicly available information

Irina P. Smirnova

Ioffe Institute, Saint Petersburg, Russia

Research Focus & Metrics

Academic Career Length

27Years (2000-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 October 2003 in Physics of the Solid State
Verified
Journal Article
Closed access
PDF file
VKV. M. Kozhevin
V. M. Kozhevin
DYD. A. Yavsin
D. A. Yavsin
ISI. P. Smirnova
I. P. Smirnova
MKM. M. Kulagina
M. M. Kulagina
SGS. A. Gurevich
S. A. Gurevich
The structural and electrical properties of thin granular metal films obtained by laser electrodispersion were studied. Such structures, which consist of amorphous copper grains 5 nm in size, were established to be extremely stable against oxidation. For instance, when oxidized in air, copper grains were covered by Cu2O oxide shells about 1 nm thick after a period of a few days, after which further growth of the oxide in thickness stopped. The oxidized close-packed structures conduct current through intergrain tunneling electron transitions, whereas in partially oxidized structures the conduction involves tunneling electron hopping between conducting ensembles made up of several nanoparticles. It was shown that the size of the nanoparticles and of the conducting ensembles can be found by analyzing the temperature dependence of the conductivity and, independently, from the I–V characteristics of the films.

1 September 2000 in Journal of Experimental and Theoretical Physics
Verified
Journal Article
Closed access
PDF file
DZD. A. Zakheim
D. A. Zakheim
IRIgor Rozhansky
Igor Rozhansky
ISI. P. Smirnova
I. P. Smirnova
SGS. A. Gurevich
S. A. Gurevich
Experimental data are presented for the temperature dependence of the conductivity of Cu: SiO2 metal-insulator composite films containing 3-nm Cu granules. At low temperatures in the concentration ran

1 July 2005 in Semiconductors
Verified
Journal Article
Closed access
PDF file
DZD. A. Zakheim
D. A. Zakheim
ISI. P. Smirnova
I. P. Smirnova
IRI. V. Roznanskii
I. V. Roznanskii
SGS. A. Gurevich
S. A. Gurevich
MKM. M. Kulagina
M. M. Kulagina
GIG. V. Itkinson
G. V. Itkinson
The design and fabrication of a high-power light-emitting diode chip that has an active-region area of 1 mm2 and emits at a wavelength of 460 nm are described. The chip structure is developed on the basis of numerical simulation and is intended for flip-chip assembly. The use of two-level interconnections for an n-type contact made it possible to obtain an unprecedentedly low series resistance (0.65 Ω) and a high uniformity of pump-current distribution. Light-emitting diodes based on the developed design operate in the continuous-wave mode in a current range of 0–2 A, and their highest emission power is 430 mW.

8 March 2013 in Semiconductors
Verified
Journal Article
Closed access
PDF file
LML. K. Markov
L. K. Markov
ISI. P. Smirnova
I. P. Smirnova
APA. S. Pavlyuchenko
A. S. Pavlyuchenko
MKM. V. Kukushkin
M. V. Kukushkin
EVE. D. Vasil’EVa
E. D. Vasil’EVa
AUA. S. Usikov
A. S. Usikov
Vertical and flip-chip light-emitting diode (LED) chips are compared from the viewpoint of the behavior of current spreading in the active region and the distribution of local temperatures and thermal resistances of chips. AlGaInN LED chips of vertical design are fabricated using Si as a submount and LED flipchips were fabricated with the removal of a sapphire substrate. The latter are also mounted on a Si submount. The active regions of both chips are identical and are about 1 mm2 in size. It is shown that both the emittance of the crystal surface in the visible range and the distribution of local temperatures estimated from radiation in the infrared region are more uniform in crystals of vertical design. Heat removal from flip-chips is insufficient in regions of the n contact, which do not possess good thermal contact with the submount. As a result, the total thermal resistances between the p-n junction and the submount both for the vertical chips and for flip-chips are approximately 1 K/W. The total area of the flip-chips exceeds that of the vertical design chips by a factor of 1.4.

5 January 2014 in Semiconductors
Verified
Journal Article
Closed access
PDF file
ISI. P. Smirnova
I. P. Smirnova
LML. K. Markov
L. K. Markov
APA. S. Pavlyuchenko
A. S. Pavlyuchenko
MKM. V. Kukushkin
M. V. Kukushkin
SPSergey Pavlov
Sergey Pavlov
Structural, optical, and electrical properties of indium-tin oxide (ITO) films produced by electron-beam evaporation, magnetron sputtering, and a combined method are studied. It is demonstrated that, despite the high transparency of the electron-beam-deposited ITO films in the visible spectral range, their conductivity and refractive index are noticeably lower than the respective parameters of ITO films deposited by magnetron sputtering. A technique for the fabrication of double-layer systems by the combination of these two deposition techniques is developed. As a result, we obtained the films, which possess the advantages of magnetron-sputtered layers and can be used as contact layers to p-type GaN in LEDs for the blue and nearultraviolet (near-UV) spectral ranges.

7 November 2009 in Semiconductors
Verified
Journal Article
Closed access
PDF file
LML. K. Markov
L. K. Markov
ISI. P. Smirnova
I. P. Smirnova
APA. S. Pavlyuchenko
A. S. Pavlyuchenko
EAE. M. Arakcheeva
E. M. Arakcheeva
MKM. M. Kulagina
M. M. Kulagina
A reflecting contact to a p-GaN layer, used in fabrication of blue flip-chip light-emitting diodes, has been produced by deposition of thin indium tin oxide (ITO) films by electron-beam evaporation. The high reflectance of the contact, which exceeds that of a Ni/Ag contact, provides a 15–20% increase in the external quantum efficiency of light-emitting crystals. The forward voltage drops for crystals with an ITO(5 nm)/Ag(220 nm) contact are comparable with the corresponding values for crystals with a Ni(1.5 nm)/Ag(220 nm) contact. The specific resistance of the contact with an ITO layer is 3.7 × 10−3 Ω cm2. It is shown that, for ITO films produced by the given method, the optimal thicknesses providing the best electrical and optical characteristics of the crystals are in the range 2.5–5.0 nm.