1 September 2011 in Powder Metallurgy
1 December 2012 in Applied Mechanics and Materials
ZZZamzahariah Mahamad Zahir
Zamzahariah Mahamad Zahir
Dry machining is an eco-friendly machining process and its importance in the manufacturing industries should be taken seriously. Machining without the use of any cutting fluid is becoming increasingly more popular due to concerns regarding the safety of the environment and reducing cost. Dry and wet turning of T6061 aluminium alloy was performed on a lathe by using Silicon Nitride (Si3N4) inserts as the cutting tool. Tool wear behaviour of Si3N4 cutting tool were studied with the aim of finding the optimum cutting conditions for both dry and wet machining. Machining was performed at four different cutting speeds; 292, 388, 518 and 689 m/min using two different cutting parameters (feed rate, f = 0.2 mm/rev, depth of cut, d = 0.1 mm and f = 0.4 mm/rev, d = 0.2 mm). Material removal rate (MRR) was also obtained and the temperature at the tool-chip interface were measured using an infrared (IR) thermometer as to see the effect of temperature rise during machining. Dry machining with smaller cutting parameters resulted in lower wear rates by 37 to 48% for all four cutting speeds. Nevertheless, reduction of wear rate by 38 to 57% was found from wet machining. The optimum cutting speed for both dry and wet machining of T6061 aluminium alloy using Si3N4 cutting tool was found to be 518 m/min for both cutting parameters. However, the optimum cutting parameters are apparently with the feed rate of 0.4 mm/rev and depth of cut of 0.2 mm. At the optimum cutting speed, the tool tip temperature for dry machining was higher than wet machining by 40 and 51% for f = 0.2 mm/rev and f = 0.4 mm/rev respectively. Dry machining of T6061 Aluminium alloy can be more suitable particularly at higher cutting speed with interrupted cutting operations.
25 January 2013 in Applied Mechanics and Materials
Dry machining is a clean machining process and it will be considered as a necessity for manufacturing industries in future. Dry machining is environmental friendly and safe to be performed. Regardless of decreasing tool life due to lack of lubricants, choosing dry machining over wet machining may be a wiser choice since the cost of purchasing and disposing the cutting fluids can contribute to a higher cost. Tool wear intensities of TiN and TiCN coated tools using both dry and traditional wet machining was studied with the aim in finding the optimum cutting speed from three different cutting speeds (318, 394 and 490 m/min) with a feed rate of 0.6 mm/rev and depth of cut of 0.4 mm. Tool tip temperature was also analyzed to see the effect of temperature rise at the tool-chip interface. TiCN coated tool performed better than TiN coated tool since the wear rate for TiCN coated tool is smaller by 40-48 % when compared to TiN coated tool for dry machining for all three cutting speeds. The optimum cutting speed for dry machining of T6061 Aluminium alloy using TiN and TiCN coated tools is 394 m/min. Tool tip temperature for dry machining is also slightly higher than wet machining by 19 and 32 % for TiN and TiCN coated tools respectively at the optimum cutting speed. Dry machining of T6061 Aluminium alloy can be a more suitable eco-friendly machining process particularly at high cutting speed for interrupted cutting operations.
28 March 2011 in Applied Mechanics and Materials
Microwave processing ceramics is emerging fast as a new field of ceramic processing and material synthesis. The past year has witnessed significant progress in the aspects of commercialization and application of the technology to new areas. Further research states that Titanium Carbide (TiC) is the best cutting tool due to its high melting point and by that reason this project aims to show the difference between conventional sintering, microwave sintering and Hot Isostatic Pressing (HIP). Two different compositions consisting of 97TiC3Ni and 93TiC7Ni were sintered using conventional furnace, microwave furnace and HIP. Density, hardness and microstructure analysis were carried out on these TiC inserts. 97TiC3Ni produced higher density and hardness values compared to 93TiC7Ni for all three different methods. Microwave sintering produced the highest density and hardness values compared to conventional sintering and HIP. Microwave produced samples with improved density and hardness in a shorter processing time which is 93% faster than conventional sintering and 50% faster than HIP.
8 October 2012 in Advanced Materials Research
Traditional wet machining methods using oil based cutting fluids and water based cutting fluids are currently being used widely in the industry. Since oil based cutting fluids contributes to environmental problems, water based cutting fluids were introduced to minimize these effects even though not extensively used everywhere in all parts of the world. Eco-friendly machining is introduced for making the environment a better and healthier place by reducing the amount of contaminants and pollution into the water system. Two biodegradable cutting fluids have been chosen in this study; vegetable oil (palm oil) and water based cutting fluids. The wear behavior of TiCN coated tools is studied for three different cutting speeds (333, 415 and 517 m/min) and at two different cutting parameters; depth-of-cut, d and feed rate, f (d = 0.2 mm, f = 0.4 mm/rev and d = 0.4 mm, f = 0.6 mm/rev). Wear rate for machining using palm oil cutting fluid is lower (longer tool life) than the wear rate obtained from using water based coolants. Palm oil has better lubrication properties compared to water based coolants which have better cooling effects. The optimum cutting parameters for machining T6061 Aluminium alloy using TiCN coated tool is found; 333 m/min (water based) and 415 m/min (palm oil) at a depth of cut of 0.4 mm and feed rate of 0.6 mm/rev.