25 April 2024 in TURKISH JOURNAL OF CHEMISTRY
The sensitizer is one of the most essential dye-sensitized solar cell (DSSC) components. In the present research, a Zn-astaxanthin complex was investigated as a sensitizer, compared to pure astaxanthin. The complex with a 1:1 mole ratio between astaxanthin and Zn2+ was synthesized in a reflux reactor at 37–60 °C. The product was analyzed using Proton Nuclear Resonance (1H-NMR), which indicates the presence of chelate formation between Zn2+ with two atoms of oxygen on the terminal cyclohexane ring of astaxanthin. The interaction of sensitizers (astaxanthin and Zn-astaxanthin) on the photoelectrode surface in this study was analyzed using a Fourier Transform Infra-Red (FTIR) and Ultraviolet-Visible Diffuse Reflectance Spectroscopy (UV-Vis DRS). The FTIR spectra of photoelectrode immersed in Zn-astaxanthin show peaks of C=O stretching and vibration -OH group at 1730 and 1273 cm–1, respectively, and H-C-H stretching vibration with high intensity in 2939, 2923, and 2853 cm–1. The UV-Vis DRS analysis shows the band gap of photoelectrode (PE), photoelectrode immersed in astaxanthin (PE/astaxanthin), and Zn-astaxanthin (PE/Zn-astaxanthin) are 3.19, 1.65, and 1.59 eV, respectively. Under illumination intensity of 300 W/m2, the maximum energy conversion efficiency of DSSC with Zn-astaxanthin as sensitizer is (0.03 + 0.0022)%, higher than DSSC with astaxanthin as sensitizer ((0.12 + 0.0052)%). Up to 70 h of illumination, DSSC with Zn-astaxanthin as a sensitizer also has better stability than astaxanthin-based DSSC.
1 June 2024 in Indonesian Journal of Chemistry
Reducing Free Fatty Acids in Crude Palm Oil Using Diethylene Glycol and Zinc(II) Chloride Based Deep Eutectic Solvent
1 January 2017 in AIP Conference Proceedings
Free fatty acids (FFA) contained in crude palm oil (CPO) and sludge oil has been used as the base material of biodiesel with the aid of a catalyst in the transesterification and esterification reactions. This study aims to synthesize and characterize bifunctional catalysts were synthesized from the ashes of palm empty fruit bunches (EFB) and alum based on the analysis of XRD, XRF and acidity test. Bifunctional catalyst obtained was used as a catalyst to production of biodiesel with different levels of FFA. The optimum ratio alum added was 0.2 mol at 3 hours of reaction time and 3% of catalyst by the FFA samples were used 67,40%. The catalyst with optimum alum mole variations subsequently used on samples with varying levels of FFA, namely 1.29%, 4.98%, 29.21%, 67.40% and 74.47%. Optimum conversion of methyl ester in the esterification reaction occurs in the sample with 67.40% FFA content, which reached 86.17%, while the conversion of methyl ester transesterification process optimum amounted to 45.70% in the samples with 4.98% FFA content. Methyl ester produced has a refractive index of 1.448 (29.8 ° C), density of 0.883 g / mL (25 °C) and a viscosity of 8.933 cSt (25 ° C). The results of GC-MS analysis showed that the main composition of methyl ester result of esterification of sludge oil methyl palmitate (36.84%), while the CPO transesterification shows the main composition of methyl ester is methyl oleic (38.87%). Based on the research results, the catalyst synthesized from alum and EFB ash can be used as a Bifunctional catalysts for biodiesel synthesis.
10 June 2020 in Indonesian Journal of Chemistry
This study aims to prepare dealuminated metakaolinite which has a high surface area by using NH4OH as an activator. The natural kaolinite sample was treated at 600 °C for 6 h in order to obtain metakaolinite. A dealuminated metakaolinite was then prepared by the repeated activation method using concentrated ammonia (5 M NH4OH) at room temperature. Depending on the nature of each type of material, natural kaolinite, NH4OH treated kaolinite, metakaolinite and NH4OH treated metakaolinite were characterized using X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), scanning electron microscopy-energy dispersive spectroscopy (SEM-EDS), and Brunauer-Emmett-Teller (BET-N2) measurements. XRD and FTIR results confirmed that structural transformation from kaolinite to metakaolinite had occurred. According to SEM-EDS data, the activation of metakaolinite by NH4OH allowed the dealumination of metakaolinite. The increase in the Si/Al ratio was almost twice as high as in kaolinite. BET-N2 analysis showed that the specific surface area and the total pore volume increased significantly after activation. Its adsorption properties were tested against bixin. Bixin adsorption on dealuminated metakaolinite followed pseudo-second order kinetic where k2 = 0.20 g/mg min. The adsorption isotherm followed the Langmuir model where qm = 0.72 mg/g.
29 May 2020 in Journal of Chemical Process Engineering
Selektivitas Adsorpsi Asam Lemak Bebas (ALB) dan Beta Karoten Minyak Sawit Mentah Menggunakan Metakaolin Teraktivasi Kalium Karbonat (K2CO3)
6 December 2025 in Agritech
This study used modified fly ash as a material to adsorb free fatty acid in Crude Palm Oil. One or two types of modification treatments in previous studies were used to investigate the effect on the absorption process. Therefore, this study focused on the capacity of the modified fly ash in adsorbing FFA with varying concentrations and durations of adsorption. Modification of fly ash began through leaching process using hydrochloric acid (HCl), followed by activation using hydrogen peroxide (H₂O₂), and reactivation using cocamidopropyl betaine (CAPB) surfactant. Scanning Electron Microscope Energy Dispersive X-Ray (SEM-EDX) is used to analyze the morphology and elements, while a Gas Sorption Analyzer (GSA) is used to analyze the pore radius, surface area, and pore volume of modified fly ash. Based on SEM-EDX result, fly ash had an amorphous shape with silicon (32.15%) and oxygen (50.29%) as the major elements. While GSA showed that the surface area, total pore volume, and average pore diameter were 15.34 m²/g, 0.02 cc/g, and 3.23 nm, respectively. Furthermore, modified fly ash had adsorption efficiency and capacity of 44.38%±0.21 and 140 mg/g±0.21, respectively. Then, adsorbent mass of 6% w/w and adsorption duration of 60 minutes recorded as the optimal condition of FFA adsorption process using fly ash. The maximum permissible FFA in cooking oil based on Standar Nasional Indonesia (2019) was 0.30%. Because of that, multi-stage adsorption was carried out to reduce the FFA in order to comply with Standar Nasional Indonesia (2019). The adsorption with twice repetition can produce CPO with FFA < 0.30% (initial FFA content of 1.2%). Due to the reduction level of FFA, the yield of the CPO obtained from each step was ±60-80%. This study could be applied in industry to reduce the FFA content and enhance the CPO quality.